Lavex 842CD123ST12 handleiding
Handleiding
Je bekijkt pagina 8 van 12
(8) Lavex 12-Gallon, 500 PSI Carpet Extractor Lavex 12-Gallon, 500 PSI Carpet Extractor (17)
4.0 Set-Up and Operation
4.1 Attach the Power Cord
The machines comes with two (2) 25-foot, 12/3-gauge safety power cords.
• Locate the pigtail on the back of the machine’s base.
• Plug the lighted end of the power cord into the pigtail.
• Plug the cord into a 20 AMP grounded wall outlet.
20 AMP circuits are normally found in kitchens and bathrooms. Never remove the ground
prong from the plug. If a circuit breaker trips during operation, turn machine o, reset the
breaker and move the electrical cord to a dierent outlet and resume operation.
4.2 Vacuum System
The extractor uses a dual vacuum motor system that provides outstanding water lift and
air ow.
Vacuum Float Assembly Warning System:
The oat assembly shut-o, located in the recovery tank on the vacuum stand pipe,
prevents the waste tank from overowing into the stand pipe and damaging the vacuum
motor. The oat assembly will cut-o vacuum to the waste tank. The motor will also
reach a fast, high-pitched sound alerting you when the recovery tank is about to over
ow. When this happens, immediately turn o the vacuum motor and empty the waste
tank. If the operator continues to use machine after the tank is full, it will VOID the
Warranty.
The oat assembly has a lter to prevent debris from entering the stand pipe. Refer to the
“Maintenance” section for removal and proper cleaning. It is also necessary to use low
foaming chemicals or a defoamer to eliminate foam build-up in the recovery tank and
damage to the vacuum motors.
If moisture enters the vacuum motors, contact an authorized service center. To prevent
moisture from damaging the vacuum motors during storage, empty the recovery tank and
store with the lid open.
4.3 Pump System
500 PSI model extractors have self-priming pumps. There is no need to prime this pump.
5.0 Maintenance
WARNING: Disconnect electrical power cord before performing any service or
maintenance inside the machine base or before testing or repairing switches or power
cords. Failure to do so may result in severe personal injury or death.
Regular maintenance is required to keep your Carpet Extractor in proper working
condition. Failure to properly maintain your machine could void warranty. Thoroughly
clean all equipment and accessories after each use:
• Rinse the solution and recovery tanks with clean water.
• Flush the pump system with clean water, including all hoses and wands.
12.0 Machine Parts List – No Heater
Drawing No. Item ID Item Description Qty.
1 SN-12-ST-LAVEX BLUE 12-Gallon Solution Tank - Lavex Blue 1.00
2 Part of Solution Tank Insert Molded into Solution Tank 1.00
3 80-0017 Bulkhead Fitting 1.00
4 Part of 80-0017 Bulk Head Fitting 1.00
5 10-0846 1/4” MPT Hex Nipple 1.00
6 10-0845 1/8” Strainer 2.00
7 80-0080-UN 500 PSI Regulator / Unloader 1.00
8 80-0026 3/8” Barb x 1/4 MPT 90 Degree 3.00
9 10-0826 3/4” Hose Clamp 5.00
10 80-0001 Extractor Exhaust Hose 0.40
11 80-0003-A 1-1/2” Black Lined Gray Hose 2.00
12 10-0806 1-1/2” Grey Hose Barb Fitting 1.00
13 Bracket Part of 80-0016 Pump 1.00
14 80-0006 45 Degree Street Elbow 1.00
15 80-0011 90 Degree Street Elbow 1.00
16 10-0803 Splash-proof Switch 3.00
17 80-0059 500 PSI Gauge 1.00
18 80-0013 500 PSI Switch Plate 1.00
19 Connector Part of 80-0059 Gauge 1.00
20 SN-12-L-LAVEX BLUE 12-Gallon Lid - Lavex Blue 1.00
21 80-0010 1/4” Brass Tee 2.00
22 80-0011-2 90 Degree Street Elbow 1.00
23 80-0004 1/4” x 4” Brass Nipple 1.00
24 10-0852 1/4” 90 Degree Brass Elbow 3.00
25 10-0804-A Hatch Cover Gasket 1.00
26 10-0804 Hatch Cover 1.00
27 80-0012 Float Assembly 1.00
28 10-0416-A 1-1/2” Black ABS Stand Pipe 1.30
29 80-0008 1.5 PVC Female Adapter 1.00
30 SN-12-RT-LAVEX BLUE 12-Gallon Recovery Tank – Lavex Blue 1.00
31 10-0805 Dump Valve for Extractor 1.00
32 10-0849 1-1/2” ABS Fitting 1.00
33 10-0155 Hose Cu Straight 1.00
34 10-0848-B 1-1/2” 90 Degree ABS Street Elbow 3.00
35 10-0833 Motor Manifold Bolts 6.00
36 80-0116 Spacer for 3-Stage Extractor Motor Only 6.00
37 80-0811 2-Stage Extractor Motor 2.00
37 10-0810 3-Stage Extractor Motor 2.00
38 10-0838-A Complete Pigtail (1 or 2 Depending on Model) 1.00/2.00
39 10-0850 Strain Relief for Pigtail - Part of 10-0838-A 1.00/2.00
39 10-0851 Strain Relief Nut for Pigtail - Part of 10-0838-A 1.00/2.00
40 10-0822 Exhaust Grate 3.00
41 10-1030-S2 2-Stage Extractor Motor Gasket 2.00
41 10-1030-S3 3-Stage Extractor Motor Gasket 2.00
42 SN-12-MFLD Extractor Motor Manifold 2.00
43 10-0830 Hinge Keeper 1.00
44 10-0821 Extractor Hinge 2.00
45 10-0820 End Cap for Rod on Extractor 2.00
46 SN-12-MB-DRGRY 12-Gallon Motor Base – Dark Grey 1.00
47 10-0836 19” Axle 1.00
48 10-0807 Wheels 1.00
49 10-0834 Pump Flat Washer 18.00
Bekijk gratis de handleiding van Lavex 842CD123ST12, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Lavex |
| Model | 842CD123ST12 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3724 MB |
