KStrong Wrangler UFA40010 handleiding
Handleiding
Je bekijkt pagina 4 van 8
Do not alterand misuse the equipment.
NOTE:
Ÿ Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects, machinery,
abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent Person before fall
protection equipment is selected.
Ÿ The analysis of the workplace must anticipate where workers will be performing their duties, the routes they will take to
reach their work, and the potential and existing fall hazards they may be exposed to. Fall protection equipment must be
chosen by a Competent Person. Selections must account for all potential hazardous workplace conditions. All fall
protection equipment should be purchased new and in an unused condition.
Ÿ Fall protection systems must be selected and installed under the supervision of a Competent Person, and used in a
compliant manner.
Ÿ Fall protection systems must be designed in a manner compliant with all federal, state, and safety regulations.
Ÿ Forces applied to anchors must be calculated by a Competent Person.
Ÿ Harnesses and connectors selected must be compliant with manufacturer's instructions, and must be of compatible size
and configuration.
Ÿ A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project specific. The rescue plan
must allow for employees to rescue themselves, or provide an alternative means for their prompt rescue.
Ÿ Store rescue equipment in an easily accessible and clearly marked area.
Ÿ Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment must be
provided by a Competent Person.
Ÿ Training must include the ability to recognize fall hazards, minimize the likelihood of fall hazards, and the correct use of
personal fall arrest systems.
Ÿ NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless explicitly certified
for such use.
Ÿ Maintenance of equipment must be done according to manufacturer's instructions. Equipment instructions must be
retained for reference.
Ÿ Prior to EACH use, all equipment in a fall protection system must be inspected for any potential or existing deficiencies that
may result in its failure or reduced functionality. IMMEDIATELY remove equipment from service if any deficiencies are
found.
Ÿ Equipment must be inspected by a Competent Person at least every six months. These inspections must be documented
in equipment instruction manual and on equipment inspection grid label.
Ÿ Equipment must be inspected for defects, including, but not limited to, the absence of required labels or
Ÿ markings, improper form/fit/function, evidence of cracks, sharp edges, deformation, corrosion, excessive heating,
alteration, excessive wear, fraying, knotting, abrasion, and absence of parts.
Ÿ Equipment that fails inspection in any way must immediately be removed from use, or repaired by an entity approved by
the manufacturer.
Ÿ No on-site repair of equipment unless explicitly permitted by the manufacturer.
Ÿ Equipment subjected to forces of fall arrest must immediately be removed from use. Snap hooks, Carabiners, and other
connectors must be selected and applied in a compatible fashion. All risk of disengagement must be eliminated. All snap
hooks and Carabiners must be self-locking and self-closing, and must never be connected to each other.
Ÿ Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there is any
reason to doubt a user's ability to withstand and safely absorb fall arrest forces or perform set-up of equipment.
Ÿ Pregnant women and minors must not use this equipment. Physical harm may still occur even if fall safety equipment
functions correctly. Sustained post-fall suspension may result in serious injury or death. Use trauma relief straps to reduce
the effects of suspension trauma. Allowable individual worker weight limit (including all equipment), unless explicitly stated
otherwise, is 130-310 lbs.
Note:- UFA40010 is provided with steel O-Rings to be used as mobile anchor for the workers to get connected to the lifeline
permanently.
WARNING- Failure to understand and comply with safety regulations may result in serious injury or death. Regulations
included herein are not all-inclusive, are for reference only, and are not intended to replace a Competent Person's judgment or
knowledge of federal or state standards.
3
Bekijk gratis de handleiding van KStrong Wrangler UFA40010, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | KStrong |
| Model | Wrangler UFA40010 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 853 MB |
