InfiRay BOLT TL35 V2 handleiding
Handleiding
Je bekijkt pagina 13 van 26
22 23
18. NON-UNIFORMITY CORRECTION
A non-uniformity correction (NUC) allows a thermal imager’s sensors
to correct its pixels and eliminate any image defects caused by pixel
drift. A NUC will be performed automatically each time the BOLT
TL35V2 is powered on.
The TL35V2 has three NUC modes, automatic(A), manual(M), and
background(B). The selected NUC mode (A, M, or B) appears on the
left side of the status bar. For instructions on setting the NUC mode
in the main menu, see Main Menu > Calibration on page30.
Automatic Mode
In automatic mode (A), the TL35V2 will perform a NUC automatically
according to the internal software algorithm. There is no need to
close the objective lens cap(15) as the TL35V2’s internal shutter
covers the sensor.
A countdown timer will appear in the status bar instead of the
calibration mode when 5seconds remain until an automatic NUC
is performed. The timer will appear only after the microbolometer
temperature has stabilized—after approximately 10 minutes of
continuous operation of the TL35V2.
NOTE: A manual NUC (see below) may be performed at any time
while in Automatic(A) mode.
Manual Mode
In manual mode (M), the user independently determines the need to
perform a NUC based on the quality of the observed image. It is not
necessary to close the objective lens cap(15) during a manual NUC,
as the internal shutter covers the sensor.
To perform a manual NUC while in manual mode (or automatic mode):
1. From the home screen, short press the Power
Button.
2. A manual NUC is performed instantly.
Background Mode
In background mode (B), the user independently determines the
need to perform a background NUC based on the quality of the
observed image. A background NUC uses less power than an
automatic or manual NUC because it does not use the imager shutter
to cover the sensor; instead, the user must close the lens cap(15).
To perform a background NUC while in background mode:
1. Close the objective lens cap(15).
2. From the home screen, short press the Power
Button.
3. A prompt to close the lens cap appears onscreen. The
background NUC starts after about 4seconds.
NOTE: If the lens is not properly covered, a temporary “image
burn” will remain in the image until the next non-uniformity
correction. This “image burn” is temporary and is not a defect or
sign of permanent damage.
19. PHOTOGRAPHY AND VIDEO
RECORDING
The BOLT TL35V2 is equipped with video recording and image
capture. All videos and photos are automatically saved to the
TL35V2’s built-in 32GB memory storage.
NOTE: Photo and video files are named with the time and date;
therefore, it is recommended to set the date and time before using
the photo and video functions. See Settings Menu > Date and
Settings Menu > Time on page39. Alternatively, the date and
time may be synchronized with one button in the InfiRay Outdoor
App.
Photography
To take a photo:
1. From the home screen,
short press the Photo
Button.
2. The image will freeze
for 0.5 seconds and
the camera
icon will
appear in the upper-left
corner of the screen.
NOTE: A red warning icon
appears next to the camera icon
in the upper-left corner of the screen when insucient memory
storage is available. Transfer video and image files to other storage
media to free up space on the memory card.
Video Recording
To record video:
1. From the home screen,
long press the Photo
Button to start a video
recording.
2. When the video recording
starts, the video recording
timer, in HH:MM:SS (hour:
minute: second) format,
appears in the upper-right corner of the screen.
Bekijk gratis de handleiding van InfiRay BOLT TL35 V2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | InfiRay |
| Model | BOLT TL35 V2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6057 MB |
