InfiRay BOLT TL35 V2 handleiding
Handleiding
Je bekijkt pagina 12 van 26
20 21
17. ZEROING THE BOLT TL35V2
The BOLT TL35V2 features a “freeze” zeroing method. To zero
theTL35V2:
1. Set a suitable target at the desired zero distance.
2. Confirm that the rifle is empty, safe, and pointed in a safe
direction, with no ammunition near the weapon.
3. Adjust the image and device settings following the steps in
the Quick Start Guide on page8, if you have not done so
already.
4. Select the zeroing profile, A, B, or C. See Main Menu > Rifle
Selection on page31.
5. Based on the distance to the target you wish to zero, select
a preset zero distance, OR customize one of the preset
zero distances to match. The TL35V2 supports custom
zeroing distances of 1to999 meters or 1to999 yards. See
Reset Zeroing Distance Menu > Zero Distance Submenu on
page32.
6. Ensure a stable platform and natural shooting position is
achieved behind the rifle.
7. Load ammunition, aim, and take one good shot at the target.
8. Make your rifle safe and observe the location of impact on the
target.
9. If the point of impact does not match the point of aim (the
center of the reticle), adjust the X/Y position of the reticle. Reset
Zeroing Distance Menu > Reticle Zeroing on page33.
10. In the submenu for the selected zero distance, center the reticle
on the aiming point and long press the Photo
and Palette
Buttons at the same time to freeze the image. The image
freeze
icon will appear below the X/Ycoordinates.
11. Select the axis (X or Y) along which to move the reticle by short
pressing the Control Turret to toggle between X and Y.
12. Adjust the X/Y position of the reticle until the reticle matches the
point of impact.
a. Rotate the Control Turret counterclockwise to move in the
positive direction: X=Right and Y=Up.
b. Rotate the Control Turret clockwise to move in the negative
direction: X=Left and Y=Down.
c. Upon moving the reticle, a white dot appears onscreen,
representing the original position of the reticle.
13. Long press the Control Turret to save the reticle position.
14. Take a confirmation shot—the point of impact should now match
the point of aim. If not, adjust the X/Y position of the reticle again.
For detailed Zeroing instructions, please see Reset Zeroing Distance
Menu > Reticle Zeroing on page33.
Navigating the Main Menu
From the home screen, long press the Control Turret to enter the
main menu.
In all menu interfaces:
• Menu icons and text turn blue to mark the current selection and
location of the cursor in the main menu.
• Use the Control Turret to navigate the menu:
• Rotate to move up and down through the menu to switch
between the menu options.
• Short press to change the current parameters for the
selected menu option, enter the submenu, or confirm
submenu changes.
• Long press to save any changes and exit to the home
screen.
• Short press the Power
Button to return to the previous menu
without saving.
• After 15 seconds of inactivity, the menu will automatically close
and the interface will return to the home screen. Changes are
not saved automatically (except changes to toggle on / o menu
items, such as Ultra-clear and Wi-Fi).
• Upon exiting from the main menu the cursor location is stored
for a single working session (until the TL35V2 is turned o).
After restarting the TL35V2 and entering the menu, the cursor
position will once again be at the first menu item.
Ultra-Clear
Bekijk gratis de handleiding van InfiRay BOLT TL35 V2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | InfiRay |
| Model | BOLT TL35 V2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6057 MB |
