Hayward Control Station NG handleiding
Handleiding
Je bekijkt pagina 17 van 74
EN
EN
English
English
Only use spare parts supplied by Hayward brands
®
Only use spare parts supplied by Hayward brands
®
Page 10 on 20 Page 11 on 20Control Station NG Control Station NG
5c. Settings
3 Settings: preferred language.
5 Settings: date and time.
7 Settings: screen brightness (0-
100%), home screen data display,
and calibration of the touchscreen.
Screen timed On/Off programming.
9 Sound: Programming the sound
transmission system for the following
functions: Keyboard (key touch),
Pop-ups (urgent messages), Alerts
(operational alarm).
11 Password: Protects access to the
user menu by setting up a password.
To create your password, type in a
combination of 5 numbers and the
system will memorise them.
13 Cell hours: Information about the
hours of operation of the cell and the
number of resets.
14 System info: Information about the
software version available on the
screen and the Power module.
15 Service menu: Menu accessible by
password. Ask your reseller for more
information.
1 2 3 4
7 8 9 10 11 12
13 14 15
5
6
5d. Filtration control
1 Filtration modes.
2 Manual: Allows the ltration process to be turned
on and off manually.
3 Filter cleaning: This mode is used to backwash
the lter.
4 Automatic: In this mode, ltration is turned on and
off according to the start and end times. These
time slots must be programmed within a single day
(midnight to midnight).
4 Smart: mode may be activated if and only if
the temperature probe has been activated. This
mode is based on the automatic mode, with its
three ltration intervals, but the ltration times are
adjusted according to the temperature. This is
done by setting two temperature parameters: the
maximum temperature, above which the ltration
times will be determined by the time slots, and
the minimum temperature, below which ltration
will be reduced to ve minutes, the minimum
operation period. Between these two temperatures,
the ltration times will be staggered linearly. The
antifreeze mode can be activated to turn the
ltration on if the water temperature falls below
2°C.
5 Heating: mode may be activated if and only if
the temperature probe and heat pump are both
activated and congured. This mode acts in the
same way as the automatic mode, but it can also
operate via a relay that controls the temperature.
The set point temperature is determined in this
menu and the system operates with a hysteresis
of one degree (for example: if the set point
temperature is 23°C, the system will start up when
the temperature falls below 22°C and shut down
only when it rises above 23°C).
Heating control OFF: The heating operates only
during the congured ltration periods.
Heating control ON: Keeps the ltration on after
the ltration period has expired if the temperature is
below the set point temperature. When the setpoint
temperature is reached, the ltration and heating
stop and only resume when the next programming
period begins.
6 Intelligent: mode may be activated if and only if
the temperature probe and heat pump are both
activated and congured. In this mode, the user
has two operating parameters: select the required
water temperature and the minimum ltration time
(minimum two hours and maximum 24 hours). The
ltration will operate for at least ten minutes every
two hours to check the temperature. The minimum
ltration time selected is divided into twelve
sections that are added to these ten minutes.
Example 1: Over twelve hours, the time is divided
between the twelve times a day when the ltration
starts up to check the temperature.
Example 2:
(12 hours x 60 minutes) / 12 = 60 minutes every
two hours. This is the ltration and heating period
every two hours. If the programmed ltration period
ends and the required temperature has not been
reached, the ltration and heating remain on until
the required temperature is reached. To minimize
the number of hours during which ltration operates
each day, this additional time will be deducted from
the next ltration periods occurring during the rest
of the day. (See the chart below).
1 2 3 4
5 6 7
•
The electrolysis and measurements will not activate unless the ltration is running.
Thermal circuit breaker /
Switch
Contactor
Pump
Intelligent mode operation if the temperature is constant
Intelligent mode operation if the temperature varies
Bekijk gratis de handleiding van Hayward Control Station NG, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Hayward |
| Model | Control Station NG |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 35381 MB |
