Furman SmartSequencer CN-1800S handleiding

Niet gecategoriseerd

Furman

16 pagina's

PDF beschikbaar

Handleiding

Rear Panel Overview

Unswitched Outlet Bank and Power Indicator

This duplex bank provides power at all times when the CN-1800S is

plugged in and operating under normal power conditions. The duplex

however, is protected by the EVS feature. The CN-1800S must have

its power recycled to clear the state. If the EVS feature is triggered, the

source voltage must return to within tolerable conditions (90V-130V) and

the EVS error must be cleared. Note: If the CN-1800S DIP Switch Posi-

tion 9 is ON or UP, the unit should self-reset and clear the state automati-

cally. These outlets, as all outlets on the CN-1800S, feature LiFT ﬁltering.

This duplex is not affected by the FORCE OFF feature and AC power will

continue to be available at the UNSWITCHED duplex even if FORCED OFF

is triggered. A Green LED to the right of this bank indicates AC power is

present.

Delay Banks

The CN-1800S rear panel provides three pairs of SWITCHED outlets.

These switched outlet pairs/duplexes are labeled DELAY 1, DELAY 2 and

DELAY 3. When the unit’s SEQUENCE ON function is initiated, DELAY 1

outlet bank receives power instantly, DELAY 2 outlet bank receives power

0-330 seconds later and DELAY 3 outlet bank receives power 0-330

seconds after DELAY 2 outlet bank is powered. When OFF is initiated, the

sequence order is reversed, with DELAY 3 losing power instantly, DELAY

2 bank losing power 0-330 seconds later and DELAY 1 outlet bank los-

ing power 0-330 seconds after DELAY 2 bank is shut down. The delay

intervals may be altered at the Time Delay Adjustment control pot and DIP

settings 1, 2, & 3. The control pot is adjustable with a screwdriver and

both features are located under the security shield, at the center of the

front panel. The combination of the Time Delay Adjustment and the DIP

setting can up provide up to 7 minutes of delay time.

COMM/

POWER

UNSWITCHED

DELAY 1

DELAY 2 DELAY 3

120~V, 50/60/HZ

15A MAX

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

DELAY 1

OUTLET BANK

DELAY 2

OUTLET BANK

DELAY 3

OUTLET BANK

COMM/

POWER

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

SmartSequencing Barrier Strip (2)

Primary poles connect OUT to Secondary

poles of next SmartSequencing device.

Secondary poles connect IN from Primary

poles of previous SmartSequencing device.

NOTE: Chain units in series.

COMM/

POWER

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

Remote Barrier Strip (1)

+12V - Main DC terminal output for

remote triggering

STAT - DC terminal output for a

remote LED indicator (ANODE)

REM - Main terminal input for remote

triggering

GND -

Terminal for remote LED status

and/or triggering (CATHODE)

Barrier Strip (1) – 4 Pin

The Remote Barrier strip allows

one or more remote location

switches to be connected to the

CN-1800S. The switch or switches

used may be either a momentary

or maintained-contact type. In the

Terminal Barrier Strips

Barrier Strip (2) – 4 Pin

The SmartSequencing Barrier Strip is used to connect and daisy-chain

other SmartSequencing units together. A pair of conductors between the

Primary OUT terminals and the Secondary IN terminals is all that is re-

quired. The recommended wire gauge is 24AWG, but other wire gauges

are possible if not available.

COMM/

POWER

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

Relay Barrier Strip (3)

FORCE OFF Provides immediate

shutdown by ﬁre alarm

Delay 3 - Provides dry contact

closures for relays

(max. 1A @ 24VDC)

Delay 3 operates with Furman MP-20, ASD-120, etc.

barrier’s top two poles. If by chance this latest Furman Sequencer,

the CN-1800S is used in conjunction with legacy Furman sequencing

products, such as the ASD-120, the DELAY 3 pole section can be used to

trigger the older product. The DELAY 3 section provides a dry contact clo-

sure timed in series with the DELAY 3 outlet bank. The DELAY 3 contact

closure will work in either normally closed (NC) or a normally opened (NO)

fashion. Please note, when the indicator DELAY 3 on the front panel is lit,

this will indicate the DELAY 3 terminal poles have shorted the Delay 3 dry

contact, Common (C) to Normally Open (NO). If all Delay LEDs are off, the

Delay 3 dry contact will short Common (C) to Normally Closed (NC).

Barrier Strip (3) – 5 Pin

This Relay Barrier strip performs

two functions. The FORCE OFF sec-

tion provides terminals for initiating

an immediate shutdown with a

dry contact closure. Fire alarms

and other safety measures can

interface this section on the

COMM/

POWER

UNSWITCHED

DELAY 1

DELAY 2 DELAY 3

120VAC, 50/60/HZ

15A MAX

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

COMM/

POWER

UNSWITCHED

DELAY 1

DELAY 2 DELAY 3

120VAC, 50/60/HZ

15A MAX

FORCE OFF

DELAY 3

+12V

STAT

REM

GND

OUT

SMARTSEQUENCING

REMOTE PORT

CLASS 2 WIRING

most basic MOMENTARY conﬁguration, only a Normally Open SPST push

button switch connected between REM and +12V is needed to initiate

a remote ON or OFF sequence. To support this conﬁguration, DIP switch

positions 4, 6, and 7 should be in the ON or UP position. The REMOTE

Barrier strip also provides for an externally mounted LED status indica-

tor using the STAT and GND pins. The Status LED should be connected

such that its Anode (the longer lead) is connected to the STAT pin and its

Cathode is connected to the GND pin.

Bekijk gratis de handleiding van Furman SmartSequencer CN-1800S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.