Frigidaire FMOS1746SS handleiding
Handleiding
Je bekijkt pagina 20 van 25
Place the mounting plate against the wall
and in
sert the toggle wings into the holes
in the wall to mount the plate.
NO
TE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting
plate touch the bottom of the cabinet when
pushed
flush against the wall and that the plate is
properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the
wall.
Tighten all bolts. Pull the plate away from
the wall to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
At
tach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Rem
ove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into
drywall and reattach the toggle wings to
3
⁄4″ (19 mm) onto each bolt.
1
Wall
Mou
nting
Plate
Spacing for
Toggles Mor
e Than
Wall Thickness
Bolt End
Tog
gle
Bolt
Tog
gle Wings
To use toggle bolts:
I
nstallation Instructions
2
O
UTSIDE TOP EXHAUST (Vertical Duct)
C
C1.
3/
8"
TO
EDGE
NOTE
:
IT IS
VERY IMPO
R
TANT TO
READ AND FO
LLOWTHE D
IRECTIO
N
S
IN THE INSTALLATION INSTRU
CTI
O
N
S
BE
FO
RE PRO
CEEDING
WITH TH
IS
REAR WA
LL TEMPLA
TE.
Thi
s
R
ea
rWa
ll Templa
te se
rves to p
ositio
n
the bo
tto
m
mou
ntin
g p
l
a
te
and
to l
oc
ate the hor
iz
ontal exhau
s
t
ou
t
let.
1. Use a levelto
chec
k tha
t the t
e
m
plate i
s
pos
itioned
ac
cu
r
a
tely.
2. L
oc
ate a
ndma
r
k at lea
st o
nestud on the left or
right
s
id
e of the centerli
ne
.
It is importa
nt to u
s
e a
t le
as
t
one
wood
sc
rew
mounted
fi
rmly
i
n
a
stud
to supp
or
t the w
eight
of
th
e mic
r
owav
e.
M
ar
k t
wo
a
d
dition
al, ev
en
ly
s
pac
ed
locations
f
o
r
the
s
uppl
ied tog
gle bol
ts.
3. Dr
i
ll hole
s in
th
e
marked locations.
Wher
e t
h
er
e is
a s
tu
d,
dr
il
l
a 3/1
6" h
ol
e
fo
r wood sc
r
ew
s. Fo
r ho
les
th
atdo not line up
w
ith a stu
d, d
rill 5/8
" h
oles fo
r
to
ggle bolts.
DO NOT
IN
S
T
AL
L THE MO
UNTING P
LATE
AT THIS
T
IME.
4. Re
m
o
v
e
the template fr
o
m
the r
ea
r wall.
5.Rev
iewth
e Ins
ta
ll
a
tionInst
r
ucti
o
n bo
ok for you
r
instal
l
a
ti
on situation.
Locate and m
ar
k holes
to ali
gn with holes in t
he
mounting
p
late.
IMP
O
RTANT
:
LO
C
AT
E
AT LEA
ST ONE STUD
ON EI
T
HERSID
E O
F
THE CENTE
R
LI
N
E.
MARK
THE LO
CATIONF
O
R 2 ADDIT
IO
NAL, EVENLY
SPACED T
OGGLE
BOLTS IN THE MO
UNTING
PLATE
AREA
.
Locate and mark
holes
to al
i
gn with holes
in t
he
mountingplate.
IMPORTANT:
LO
C
A
TE AT LEA
ST O
NESTUD ON EITHER SI
D
E OF
THE
CENTE
R
LINE
.
MARKTHE LO
CATION
FOR 2 ADDITIONA
L, EV
ENLY
SPACEDTOG
GLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the re
ar
wall tem
plate along
the dotted
line.
Trim the rear
wall templat
e along
t
he dotted lin
e.
12"
4"
Da
rl
e
v
ue
lt
a
ala
hoj
a
par
a
co
ns
u
ltar
la
ver
sió
n
enE
s
pa
ñol.
EN-20
INSTALLATION OVERVIEW
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and
secured, and that the wires are
not pinched.
. Connect Ductwork
IMPORTANT NOTES:
Attach Mounting Plate to
Wall Prepare Top Cabinet
Adapting Microwave Blower
for Outside Top Exhaust
Check Damper Operation
Mount Microwave Oven
Adjust Exhaust Adaptor
C2.
C1.
C3.
C4.
C6.
C5.
C
7
Bekijk gratis de handleiding van Frigidaire FMOS1746SS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Frigidaire |
| Model | FMOS1746SS |
| Categorie | Magnetron |
| Taal | Nederlands |
| Grootte | 4289 MB |
