Frigidaire FMOS1746SS handleiding
Handleiding
Je bekijkt pagina 16 van 25
Remove and save the screw that holds the
blower plate to the microwave. Lift off the
b
lower plate.
Back of
Microwave
I
nstallation Instructions
B2.
O
UTSIDE BACK EXHAUST (Horizontal Duct)
B
Blower Plate
REMOVE BLOWER PLATE
3/8" TO EDGE
NOTE: IT IS VE
RY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE
AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR
2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTA
NT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
Darle vuelta a la hoja para consultar la
versión en Español.
3
/8"
TO
EDGE
NO
TE
: IT IS
VERY I
M
PO
R
TANT TO
READ AND FOLLO
WT
HED
IRECTIONS
IN THE INSTALLAT
ION INSTRU
CTI
ONS
BE
FORE PR
O
CEEDINGWITH T
HIS
REAR WALL TEMPLA
T
E
.
This Rea
r
Wall T
e
mpl
ate
s
e
rves
to p
ositio
n the bo
ttom
mou
ntin
g platea
n
d
to lo
c
ate th
e h
o
ri
zon
ta
l ex
hau
st
ou
tlet.
1. Use a l
evel
to
c
h
e
ck
th
at the templa
te is p
osition
ed
a
ccur
ate
ly
.
2. Lo
ca
te and
mark at le
as
t onestu
d
on the
le
ft o
r
righ
t side o
f the
c
e
nterl
i
n
e.
It is im
po
rtant to u
se
a
t least
one
wood
scre
wmo
unted fi
r
mly in a stud
to support the weight
o
fthe mic
r
ow
ave.
Mar
k two a
dditional, e
ve
nlyspa
c
ed
lo
c
ation
s f
or the s
upplied
to
ggle
bo
lts.
3. Drill holes in
the m
arked lo
cation
s.Wher
e t
he
re is
a stud, d
r
ill
a 3/16" h
ol
e
for
woo
d s
cr
e
w
s.
For holes
that
d
o n
ot lin
e up
w
ith a s
tud, dr
il
l 5/8
"
holes fo
r
toggl
e bo
lts.
DO
NOT
I
N
S
T
A
L
L THE MOU
NT
I
N
G P
L
AT
E
AT
THIS
TIME.
4. Re
m
ove the templa
te fromthe
r
ea
r
wal
l.
5.R
evie
htw
e In
sta
llationIns
tr
uc
tion book for
your
in
stallatio
n si
tua
t
ion.
Locat
e and m
ar
k
holes
to ali
gn with holes in the
mounting
plate.
IMPO
RTANT
:
LO
C
ATE AT LEAST O
NE
STUD ON EITHER
SIDE OF
TH
E CENTER
LI
N
E.
MARKT
HE LOCATIO
N
FOR 2 ADDITIONAL, EVENLY
SPACED TO
GGLE
BO
LTS IN
THE MO
UNTING
PLATE
AREA.
Locate and mar
k holes
to al
ign with holes
in the
.
e
t
alpgnitnuom
IMPO
RTANT
:
LO
CAT
E AT LEAST ONESTUD ON EITHER SIDE O
F
THE
CENTE
R
LINE.
MARKT
HE LOCATIONF
O
R 2 ADDITION
A
L, EVENLY
SP
ACEDTO
G
GLE BO
LTS IN
THE MOUNTING PLATE
AREA.
Trim the r
ear wall temp
lat
e alongt
he dotted
line.
Trim the rear
wal
l t
em
pla
t
e along
t
h
e dotted line.
12"
4"
Dar
l
ev
u
elt
aa la ho
j
apar
a
consul
t
a
r
la
v
e
r
s
i
óne
nEs
pa
ño
l.
EN-16
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
B1.
You need to cut an opening in the rear
wa
ll for outside exhaust.
• Rea
d t
he instructions on the REAR
WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions
of the REAR WALL TEMPLATE.
•
•
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Att
ach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
Make sure the screws for the
blo
wer motor and blower
plate are securely tightened
when they are reinstalled. This
will help to prevent excessive
vibration.
Make sure the motor wiring
has been properly routed and
secured, and that the wires
are not pinched.
Bekijk gratis de handleiding van Frigidaire FMOS1746SS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Frigidaire |
| Model | FMOS1746SS |
| Categorie | Magnetron |
| Taal | Nederlands |
| Grootte | 4289 MB |
