Festool CTM 36 EI AC handleiding
Handleiding
Je bekijkt pagina 23 van 132
7.1 Connecting a power tool
WARNING
Risk of injury
► Observe the maximum electrical outlet
module connected load (see "Technical da
ta" section).
► Switch off the power tool.
Connecting a mains-powered power tool to the
mobile dust extractor
► Connect the power tool to the electrical out
let module[1-3].
☑ The power tool is connected to the mobile
dust extractor via the power cable.
Connecting a battery-powered power tool to
the mobile dust extractor
► In standby mode, press the connection but
ton[1-8].
The connection display[1-7] flashes slowly.
For a period of 60 seconds, the mobile dust
extractor is ready for connection.
► Turn on the battery-powered power tool.
The mobile dust extractor starts up and the
battery-powered power tool is connected
until the mobile dust extractor is manually
switched off or the mains plug is disconnec
ted. The cordless tool must then be connec
ted again.
Connecting a new battery-powered power tool
overwrites the previous connection.
7.2 Connecting the CT-F I remote control
Connecting the remote control and the mobile
dust extractor
To be able to connect a remote control to a
mobile dust extractor, the remote control must
be reset (see "Resetting the remote control").
A remote control that has not been connected
previously can be connected directly.
A connection that has been established
between the remote control and the mo
bile dust extractor will persist even after
the mobile dust extractor has been man
ually switched off or the mains plug has
been disconnected.
► Hold down the connection button[1-8] on
the mobile dust extractor for threeseconds
in standby mode.
The connection display[1-7] flashes rapid
ly.
For a period of 60seconds, the mobile dust
extractor is ready for connection.
► Press the MAN button on the remote con
trol.
The remote control is permanently stored in
the mobile dust extractor.
Switching on/off
Once the remote control is connected to the
mobile dust extractor, the mobile dust extractor
can be switched on and off with the remote con
trol.
► Press the MAN button on the remote con
trol to switch the device on and off.
Resetting on the remote control
Resetting deletes the connection between a re
mote control and the mobile dust extractor.
► Hold down the connection button and the
MAN button for tenseconds.
The LED indicator lights up purple if the
reset has taken place.
7.3 FestoolApp*
The mobile dust extractor can be configured
with the FestoolApp.
► Hold down the connection button[1-8] on
the mobile dust extractor for three seconds
in standby mode.
The connection display[1-7] flashes rapid
ly.
For a period of 60seconds, the mobile dust
extractor is ready for connection.
► Follow the instructions provided in the
FestoolApp.
*Not available in all countries.
8 Settings
8.1 Adjusting the hose diameter
Adjustment of the hose diameter is only possi
ble in standby mode.
► Use the buttons of the hose diameter ad
juster[1-12] to adjust the inner diameter of
the connected suction hose.
☑ The adjustment is stored in the mobile dust
extractor.
This ensures that the air speed in the ex
tractor hose is measured correctly (see
section8.6).
8.2 Adjusting the suction power
► Press the plus or minus button[1-12] while
extracting.
8.3 Connecting sleeve
The bypass function of the connecting
sleeve prevents strong suction from sanding
English
23
Bekijk gratis de handleiding van Festool CTM 36 EI AC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Festool |
| Model | CTM 36 EI AC |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 14883 MB |
