Festool CTM 36 EI AC handleiding
Handleiding
Je bekijkt pagina 24 van 132
machines and floor nozzles on smooth surfa
ces.
Open
► Turn the adjusting ring to the "OPEN" posi
tion.
Close
► Turn the adjusting ring to the "CLOSE" posi
tion.
8.4 Applying the brake
Folding out the black brake lever[1-18] pre
vents the mobile dust extractor from rolling. To
achieve this, lift the front end of the mobile dust
extractor slightly and push the black brake lev
er downwards until it latches into place. Press
the release button[1-17] to release it.
8.5 Temperature cut-out
A temperature cut-out switches the mobile dust
extractor off when it reaches a critical tem
perature to prevent overheating. The bottom
LED[1-11] indicates a fault.
LED lights up red Excessive temperature
► Switch off the mobile dust extractor, let it
cool down.
► Switch on the mobile dust extractor again
after approx. five minutes.
8.6 Volumetric flow monitoring
For safety reasons, an acoustic warning signal
sounds if the air speed in the suction hose
falls below 20m/s (dust class M only). For the
volumetric flow monitoring to function correct
ly, this requires the use of Festool suction ho
ses with an inner diameter of 21mm to max.
42mm.
The table* on the mobile
dust extractor explains this
connection for the minimum
required extraction volume
of the respective hose diam
eter. If the rate is below the
respective extraction volume, a warning signal
is emitted.
*only with EU versions of CT AC
Possible causes Solution
Value set on the
suction power adjust
ment[1-11] is too
low.
Set the suction pow
er adjustment to a
higher value (see sec
tion8.2).
Mobile dust extractor
not set to the correct
hose diameter.
Set the correct hose
diameter (see sec
tion8.1).
Suction hose is
blocked or kinked.
Eliminate the cause
of the clogging or
straighten the hose.
Filter bag full. Insert a new filter bag
(see section10.1).
Dirty main filter. Change the main filter
(see section10.3).
AUTOCLEAN ONLY:
Clean the main filter
(see section9.2).
Electronic monitoring
malfunction.
Have the fault recti
fied by a Festool serv
ice workshop.
Wet extraction. Function not impaired,
no measures re
quired.
ONLY CTM36EAC-
LHS with PLANEX
LHS2225:
In tasks that require
a low extraction set
ting (e.g. on soft sur
faces).
Activate the bypass
function on the special
extraction sleeve[1A].
9 Working
9.1 Handling
Hose holder: After finishing work, you can feed
the suction hose through the opening[8-2] and
place it in the hose holder.
SYS-Dock Systainer storage area: A Systainer
can be fastened to the storage area with the
four slides or the T-Loc lock[8-1].
9.2 AUTOCLEAN – cleaning the main filter
(variants with AUTOCLEAN only)
Only in conjunction with a disposal bag
(to comply with dust class M). Not for
use during wet extraction.
Switching automatic dedusting on and off
► In standby mode, press the AC but
ton[1-10] to switch AUTOCLEAN on or off.
English
24
Bekijk gratis de handleiding van Festool CTM 36 EI AC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Festool |
| Model | CTM 36 EI AC |
| Categorie | Stofzuiger |
| Taal | Nederlands |
| Grootte | 14883 MB |
