Daikin EWWS490VZXSA1 handleiding
Handleiding
Je bekijkt pagina 19 van 67
D-EOMZC00106-17_07EN - 19/67
4.2.1 Thermostat Ctrl
This page resumes all the parameters related to the unit thermostatic control.
Setpoint/Sub-Menu
Default
Range
Description
VZ
Start Up DT=
2.7°C
0.0…5.0°C
Offset to start thermostat control
Shut Dn DT=
1.5°C
0.0…1.7°C
Offset to standby
Stg Up DT=
0.5°C
0.0…1.7°C
Offset to allow compressor starts
Stg Dn DT=
0.7°C
0.0…1.7°C
Offset to force one compressor off
Stg Up Delay=
3 min
0…60 min
Compressor start interstage
Stg Dn Delay=
3 min
3…30 min
Compressor stop interstage
Strt Strt Dly=
15min
15…60 min
Compressor Start to Start delay
Stop Strt Dly=
3min
3…20 min
Compressor Stop to Start delay
Ice Cycle Dly=
12h
1…23h
Ice cycle delay
Lt Ld Stg Dn %=
20%
20…50%
Circuit capacity threshold to stage down one compressor
Hi Ld Stg Up %=
50%
50…100%
Circuit capacity threshold to stage up one compressor
Max Ckts Run=
2
1…2
Limit to the number of circuit to be used
C1 Sequence #=
1
1…2
Manual sequence of circuit #1
C2 Sequence #=
1
1…2
Manual sequence of circuit #2
Next Crkt On=
0
-
Shows next circuit to be started up
Next Crkt Off=
0
-
Shows next circuit number to be stopped
4.2.2 Network Ctrl
This page resumes all settings related to Network control.
Setpoint/Sub-Menu
Default
Range
Description
VZ
Control Source=
Local
Local, Network
Control source selection: Local/BMS
Act Ctrl Src=
N/A
Local, Network
Active control between Local/BMS
Netwrk En SP=
Disable
Enable, Disable
Enable unit command from BMS
Netwrk Mode SP=
Cool
-
Cool, Ice, Heat (NA), Cool/Heat Recovery
Netwrk Cool SP=
6.7°C
-
Cooling setpoint from BMS
Netwrk Cap Lim=
100%
-
Capacity limitation from BMS
Netwrk HR SP=
N/A
-
Heat recovery setpoint from BMS
Network Heat SP=
45.0°C
-
Heating setpoint from BMS
Netwrk Ice SP=
-4.0°C
-
Ice setpoint from BMS
Netwrk Current SP=
800A
-
Sepoint for current limitation from BMS
Remote Srv En=
Disable
Enable, Disable
Remote server enable
4.2.3 Pumps
This page contains the settings to define the operation of the primary/backup pumps, the running hours of each pump and
all parameters to configure the behavior of the pump driven with an inverter.
Setpoint/Sub-Menu
Default
Range
Description
VZ
Evp Pmp Ctrl=
#1 Only
#1 Only, #2 Only, Auto,
#1 Primary, #2 Primary
Set number of Evaporator pumps operational and which
priority.
Evap Recirc Tm=
30s
0…300s
Water recirculating timer
Evap Pmp 1 Hrs=
0h
Running Hours Evaporator Pump 1 (if present)
Evap Pmp 2 Hrs=
0h
Running Hours Evaporator Pump 2 (if present)
Cnd Pump Ctrl=
#1 Only
#1 Only, #2 Only, Auto,
#1 Primary, #2 Primary
Set number of Condenser pumps operational and which
priority.
Cond Pmp 1 Hrs=
0h
Running Hours Condenser Pump 1 (if present)
Cond Pmp 2 Hrs=
0h
Running Hours Condenser Pump 2 (if present)
Bekijk gratis de handleiding van Daikin EWWS490VZXSA1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Daikin |
| Model | EWWS490VZXSA1 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9055 MB |
