Carel iJW handleiding
Handleiding
Je bekijkt pagina 19 van 104
19
ENG
iJW +0300103EN rel. 1.1 - 31.03.2025
Index
4.2 User terminal
3
1
2
2
1
22
3
Key:
1 Display
2 Icons/buttons
3 Icons
Fig. 4.a Fig. 4.b
Notice:
• the user terminal can only be used to set the frequent parameters and display the value of the probes connected to iJW. The
other parameters are set using the Applica app or the Applica Desktop confi guration software, depending on the access pro-
fi le. See the parameter table and the paragraph “Parameter categories visible on the user terminal”;
• Parameter /t1 is used to choose the variable to be shown on the display during normal operation:
• Parameter /5 is used to change the unit of measure .
• Parameter /d6 is used to choose the value to be shown on the display when defrosting:
Code Description Def. Min Max UOM User User terminal
/5 Unit of measure: 0 = °C; 1 = °F 0 0 1 - U YES
/6 Display decimal point: 0 = Yes; 1 = No 0 0 1 - S NO
/t1
Display on user terminal:
0 = Not confi gured 4 = value of S4 10 = virtual probe
1 = value of S1 5 = value of S5 11 to 14 = not available
2 = value of S2 6 to 8 = not available 15 = actual control set point
3 = value of S3 9 = control probe
9 0 15 - S NO
d6 Display on terminals during defrost:
0 = temperature alternating with ‘dEF’; 1 = freeze display; 2 = ‘dEF’
102- U NO
Tab. 4.a
Keypad
Icon/button Description On Flashing
Defrost Active / can be deactivated from the keypad Waiting / can be activated from the keypad
On/Off • Command activation: on / can be switched off from the keypad
• Return to the previous level in the parameters menu
Off / can be switched on from the keypad
Set point Access to temperature / humidity set point -
Light Active / can be deactivated from the keypad Waiting / can be activated from the keypad
UP arrow • Decrease value or scroll menu
• Auxiliary function: active / can be deactivated from the keypad
Auxiliary function: waiting / can be
activated from the keypad
Programming
(PROG)
Pressed briefl y:
• activate buttons
• enter menu branch
• Save value and return to the parameter code
Pressed and held (3 s):
• enter programming mode
-
DOWN arrow • Decrease value or scroll menu
• Auxiliary function: active / can be deactivated from the keypad
Auxiliary function: waiting / can be
activated from the keypad
Auxiliary function Active / can be deactivated from the keypad Waiting / can be activated from the keypad
Compressor Active Waiting
Evaporator fan Active -
Auxiliary load Active -
°C/°F Unit of measure: temperature °C/ °F -
% rH Unit of measure: relative humidity % -
HACCP Active HACCP alarms -
Service Active alarms -
Tab. 4.b
Notice: during navigation, the buttons will be on/fl ashing only if enabled.
Code Description Def. Min Max UOM User User terminal
GF Custom function associated with the specifi c button (Large models only):
0 = Not confi gured; 1 = Light; 2 = Auxiliary output; 3 = Continuous cycle.
303- S YES
GF1 Custom function associated with the UP arrow - see GF 2 0 3 - S YES
GF2 Custom function associated with the DOWN arrow - see GF 1 0 3 - S YES
A custom function can be associated with the UP arrow, DOWN arrow and auxiliary function button, choosing between unit
On/Off , light on, auxiliary output activation and continuous cycle activation, by setting parameters GF1, GF2 and GF. Parameter
GF is available only on Large models and corresponds to the specifi c button, while parameters GF1 and GF2 are available on all
models.
Bekijk gratis de handleiding van Carel iJW, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Carel |
| Model | iJW |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14964 MB |
