Camry CR 7075 handleiding

Handleiding

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248/ 248

Afdrukken

Je bekijkt pagina 10 van 248

10

LOADING THE DEVICE

Removal and installation of the battery module (13) - see Figure 1.

1. Pull and hold the battery release button (A), then pull out the entire battery module (13). The battery module (13)

will be detached from the motor housing (1).

2. Tighten the battery module (13) until you hear a click, which means that the battery module (13) has been properly

installed.

Charging methods:

Charging method 1 - look at Figure 3A:

Connect the power adapter (5) to an electrical outlet and the charging port (H) on the motor housing (1). During

charging, the battery indicator (B.III) flashes on the LED touch screen (B). When fully charged, the battery indicator

(B.III) on the LED touch screen (B) will light up continuously.

Charging method 2 - look at Figure 3B:

There is a release button (G) on the wall bracket (8). Press the release button (G) to mount the motor housing (1) on

the wall bracket (8). Then connect the power adapter (5) to the electrical outlet and charging port (J) located on the

side of the wall bracket (8). ). During charging, the battery indicator (B.III) flashes on the LED touch screen (B).

When the battery module (13) is finished charging, press the release button (G) again to remove the motor housing (1).

1. To achieve maximum charging capacity, fully charge the battery module (13) before using this unit.

2. The charging time is approximately 4-5 hours.

3. When the battery module (13) is fully charged (after 4-5 hours), disconnect the power adapter (5) from the charging

port to prevent overloading.

4. Two rechargeable modules are included, charge them before the next use, this way you can double the working time

to more than 114 minutes when vacuuming at low power.

USE

The device is designed for the care of hard floors (stoneware, terracotta, panels, parquet) in a house with an area of up

to 150m2. It has 2 functions: dry and wet cleaning of hard floors described below.

DRY VACUUMING FUNCTION

1. Mount the desired brush:

- Use the LED DUST SCANNER™ electric brush (2) to clean hard floors.

- For hard-to-reach areas, use the crevice nozzle (7).

- Use the upholstery brush (6) to clean a sofa or car seat.

2. Press and hold the power button (C) for about 3 seconds to turn on the device. The designed start-up mode is a high

level of suction power.

3. MANUAL MODES - look at Figures 6A, 6B and 6C.

Touch the white fan icon (B.V.) on the LED touch screen (B) to adjust the suction power between low (Figure 6A),

medium (Figure 6B) and high suction power (Figure 6C) by pressing again. The bar under the white fan will become

proportionally longer for medium suction power and the longest for high suction power.

Average run time on one fully charged battery: 57 minutes for low power / 40 minutes for medium power / 15 minutes

for maximum power.

4.AUTOMATIC MODE - look at Figures 6D, 6E and 6F.

Touching the AUTO icon (B.VI.) on the LED touch screen (B) activates the automatic mode. When the automatic

mode is activated, the AUTO (B.VI.) icon flashes. Automatic mode is equipped with a dust sensor that adjusts the

suction power according to the degree of dirt on the surface for effective cleaning. The current suction power in

AUTO mode is shown by the color of the ring around the LED screen:

AUTO mode low suction power - blue light ring around the LED screen (Figure 6D),

AUTO mode middle suction power - red light ring around the LED screen (Figure 6E),

AUTO mode high suction power - purple light ring around the LED screen (Figure 6F),

5.Press the power button (C) again to turn off the device.

6. If the LED DUST SCANNER™ electric brush for hard floors (2) and the aluminum tube (4) are blocked, the brush

icon (B.I) will flash, the unit has a safety program that causes the unit to stop working. The brush may block on carpets

with long pile, it is designed for hard floors. If this has happened, first remove the clogged dust and other objects.

Once the brush and tube are completely cleaned, turn the unit back on and continue working.

WET CLEANING FUNCTION

Do not use the electric mop brush (3) to clean floors soaked in water or other liquids. This will cause damage to the

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248/ 248

Bekijk gratis de handleiding van Camry CR 7075, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Stofzuiger