Camry CR 7075 handleiding

Handleiding

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248/ 248

Afdrukken

Je bekijkt pagina 11 van 248

11

vacuum cleaner. The role of the electric mop brush (3) is to dispense water onto the floor, not to extract liquid from the

floor surface.

1.Open the water tank lid (3B) on the electric mop brush (3) and pour in the water. Do not use foaming cleaners or

bleach for the mop brush.

2.Close the water tank lid (3B).

3. Mount the electric mop brush (3) to the tube (4) by releasing the button (E), then mount the tube with the brush to

the motor housing (1) by releasing the button (D) in the motor housing.

4. Unlock the water supply by turning the water supply knob (3A) to the position marked by the open padlock icon on

the surface of the water tank. Now the water will flow from the center of the round washers (12).

5. Turn on the vacuum cleaner by pressing and holding the power button (C) for about 3 seconds. Now both pads (12)

will start rotating, you can start wet cleaning the hard floor. Average run time on one fully charged battery: 17

minutes.

6. To stop the water flow, turn the water inlet knob (3A) to the position marked by the closed padlock icon on the

surface of the water tank.

TROUBLESHOOTING

Problem #1: The unit is not working.

Possible cause of problem #1: The battery module (13) is exhausted.

Solution to problem #1: Check the battery status on the LED touch screen (B). If the battery level is low, charge the

battery module (13).

Problem #2: The unit does not vacuum or has weak suction power.

Possible cause of problem #2: The dust container (14) is full.

Solution to problem #2: Empty the dust container (14).

Possible cause of problem #2: Battery power is insufficient.

Solution to problem #2: Charge the battery module (13).

Problem #3: Dirt leakage.

Possible cause of problem #3: The dust container (14) is full.

Solution to Problem #3: Empty the dust container (14).

Possible cause of problem No. 3: The release button (F) on the bottom of the dust container (14) is not locked.

Solution to Problem No. 3: Make sure the release button (F) is locked.

Problem No. 4: The motor unit (1) cannot suck when connected to the floor brush (2)

Possible cause of problem No. 4: The dust container (14) is full.

Solution to Problem No. 4: Empty the dust container (14) and clean the dust container (14) and filters (15 and 16).

Solution to problem 4: Make sure the holes and aluminum tube (4) are not blocked by debris. If they are blocked,

remove the dirt.

CLEANING AND MAINTENANCE

I. Dust cleaning - look at figure 5

Turn off the device and remove the tube (4). Place the complete motor housing (1) over the dustbin or toilet seat, press

the dust container release button (F), the container (14) will open from the bottom and the dust will fall. In addition,

when the dust container is full, the airflow icon (B.II) flashes, turn off the unit and remove the dust from the dust

container.

II. Cleaning the filters - look at Figure 7

1. Dirty filters will reduce the cleaning efficiency, as the suction power will be lower. It is strongly recommended to

clean the filter regularly after each use. Filters should be taken apart before cleaning, do not pour water into the dust

container (14) to clean the filter, as this will definitely damage the device - see Figure 8. Filters are located inside the

dust container (14), so remove them first dust.

D2. To remove the stainless steel mesh filter (15) and EPA filter (16), follow Figures 7A and 7B. To unlock them, turn

the filters counterclockwise. The stainless steel mesh filter (15) is on the outside, and the EPA filter (16) is on the

inside. Before cleaning, both filters should be removed from the dust container (14).

2.A. Cleaning the stainless steel mesh filter (15)

After removing the stainless steel mesh filter (15), clean it with a dry brush.

2.B. Cleaning the EPA filter (16)

Shake off the EPA filter (16) from dust, clean it with a dry brush and finally wash it with tap water. It is important to

completely dry the EPA filter (16) before reinstalling it.

2.C. Cleaning the sponge filter

This is a built-in air outlet filter that cannot be cleaned due to the fact that it cannot be removed, so it is not shown in

the drawings.

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248/ 248

Bekijk gratis de handleiding van Camry CR 7075, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Stofzuiger