Cambium Networks XMS Cloud handleiding
Handleiding
Je bekijkt pagina 5 van 90
let’s say that AppleTV is using wireless to connect to an SSID that is associated with VLAN 56, and
the wireless client is on an SSID that is associated with VLAN 58. Normally the wireless client would
not be able to use Bonjour to discover the AppleTV because they are on separate VLANs. But if you
add VLANs 56 and 58 to the VLAN Forwarding list, then the wireless client will be able to discover
the AppleTV.
5. In VLAN Overrides, associate one or more VLANs to pre-existing or new tags.
To configure additional settings, see “Advanced Settings”.
Advanced Settings
To configure more settings, click Show Advanced link.
l DiscoveryProtocol
n LLDP—Link Layer Discovery Protocol is a Layer 2 network protocol used to share information (such as the
device manufacturer and model, network capabilities, and IP address) with other directly connected
network devices. APs can both advertise their presence by sending LLDP announcements, and gather and
display information sent by neighbors. LLDP Interval controls how often the Access Point sends out LLDP
announcements advertising its presence. LLDP information received from neighbors is retained for LLDP
Hold Time before aging out of the Access Point’s neighbor list. Thus,if a neighbor stops sending
announcements, it will no longer appear in an AP’s LLDP List after LLDP Hold Time seconds from its last
announcement.
Request Power - If this is set to Yes and LLDP discovers a device port that supplies power to this
Access Point (on a powered switch, for example), the Access Point checks that the port is able to
supply the peak power that is required by this Access Point model. The Request Power feature does
this by requesting this peak power (in watts) from the PoE source, and it expects the PoE source to
reply with the amount of power allocated. If the Access Point does not receive a response
confirming that the power allocated by the PoE source is equal to or greater than the power
requested, then the Access Point issues a Syslog message and keeps the radios down for ten
minutes. The radios may be enabled manually after this. Using this feature provides a more graceful
way of handling an under powered situation on an AP. When the radios are turned off, a syslog
message is created—finding this is easier than hunting down an intermittent problem.
n CDP—Cisco Discovery Protocol is a layer 2 network protocol used to share information (such as the device
manufacturer and model, network capabilities, and IP address) with other directly connected network
devices. Cambium Xirrus APs can both advertise their presence by sending CDP announcements, and
gather and display information sent by neighbors. CDP Interval controls how often the AP sends out CDP
announcements advertising its presence. CDP information received from neighbors is retained for CDP
Hold Time before aging out of the neighbor list.
l DHCP Pool (for APs only)— select Yes to Enable DHCP Pool Settings if you want to set up the APs in this profile to
be DHCP servers for the clients that connect to the APs. This setting allows each AP to provide wireless clients
with IP addresses and other networking information. The IP addresses come from a DHCP Pool that you define.
The DHCP server will not provide DHCP services to the wiredside of the network. If you do not use the DHCP
server on the AP, then your wired network must be configured to supply DHCP addresses and gateway and DNS
serveraddresses to wireless clients.
n NAT — Select Yes to enable Network Address Translation on APs. NAT translates addresses on your
private IP network into legal addresses for Internet traffic, and vice versa. NAT is enabled by default.
n LeaseTime — A station is given (leased) an IP address for this amount of time. The lease must be renewed
before the lease time is up. The renewal process is managed automatically by the station and the server.
n Lease IP Range—Enter a Start and End IP address to define the range of IP addresses on your sub network
that can be given out by APs in this profile.These addresses are divided evenly among the member APs,
5 | Help Guide | XMS Cloud
Bekijk gratis de handleiding van Cambium Networks XMS Cloud, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Cambium Networks |
| Model | XMS Cloud |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13480 MB |
