Handleiding
Je bekijkt pagina 10 van 24
en Installation instructions
– Connect with flexible hose. The hose assembly
must comply with AS/NZS 1869, 10mm ID, class
B or D, no more than 1.2m long and installed in
accordance with AS/NZS 5601.1.
Note
If installing with a hose assembly:
Ensure that the hose assembly is restrained from ac-
cidental contact with the flue outlet of an underbench
oven.
Ensure that the hose does not contact the hot sur-
faces of the hotplate, oven, dishwasher or any other
appliance that may be installed underneath or next to
the hotplate.
The hose should not be subjected to abrasion, kink-
ing or permanent deformation.
The hose should be able to be inspected along its
entire length with the cooktop in the installed position.
Unions compatible with the hose fittings must be
used and all connections tested for gas leaks.
Before leaving
It should be expressly noted that we cannot accept any
liability for direct or indirect damage caused by wrong
connection, leakage or improper installation.
Check all connections for gas leaks with soap and
water. DO NOT use a naked flame for detecting
leaks.
Ignite all burners both individually and concurrently to
ensure correct operation of gas valves, burners and
ignition.
Turn gas taps to low flame position and observe sta-
bility of the flame for each burner individually and all
together.
Adhere the duplicate data plate to an accessible loca-
tion near the hotplate.
When satisfied with the hotplate, instruct the user on
the correct method of operation.
In case the appliance fails to operate correctly after
all checks have been carried out, refer to the author-
ised service provider in your area.
When being repaired, the appliance must always be dis-
connected from the mains supply; if required, notify our
customer service.
2.8 Converting the cooktop from Natural Gas
to ULPG
All work involved in installation, setting and adaptation
to a different gas type must be carried out by a licensed
gas fitter and must comply with current regulations and
the conditions laid down by the local gas company.
Before conversion the cooktop must be disconnected
from the electricity and gas valves must be turned to the
OFF position.
Removing the outer glass plate
1.
Remove the pan supports, burner caps, distributors
and rotary knobs.
2.
Undo the screws on the burners.
3.
Carefully remove the glass plate.
Removing the circuit board
Tip: The circuit board is secured to the holder by fasten-
ing pins at the sides and in the middle. Push the fasten-
ing pins carefully without damaging them. If one of the
pins breaks, the entire holder must be replaced.
ATTENTION
The circuit board can be damaged by improper hand-
ling.
Handle the circuit board carefully.
Use anti-static shields or hold the circuit board at the
edges.
Never touch the surfaces of the circuit board on
which there are components or conducting tracks.
Further information:
1
Adjusting the taps
Requirement: The upper part of the appliance and the
circuit board are removed.
"Removing the outer glass plate", Page10
1.
Remove the cylindrical parts and springs from the fit-
tings spindle.
2.
Adjust the bypass screws:
A: For ULPG, the bypass screws must be tightened
properly.
B: For Natural Gas, the bypass screws must finish
flush with the fitting.
Injectors
Request change-over injectors from our customer service deparment. Refer injector chart below for sizes.
Burner NG
Hourly gas con-
sumption (MJ)
NG
Injector mark
ULPG
Hourly gas con-
sumption (MJ)
ULPG
Injector mark
Economy burner 4.00 88 3.20 50
Standard-output
burner
6.85 116 5.50 66
10
Bekijk gratis de handleiding van Bosch PRS9A6H40A, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bosch |
| Model | PRS9A6H40A |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 2647 MB |
