Bosch GGC 18V-12 Professional handleiding

Niet gecategoriseerd

Bosch

267 pagina's

PDF beschikbaar

Handleiding

/ 267

Je bekijkt pagina 21 van 267

English | 21

LED Capacity

2× continuous green light 30–60%

1× continuous green light 5–30%

1× flashing green light 0–5%

Battery model ProCORE18V...

LED Capacity

5 × continuous green light 80–100%

4 × continuous green light 60–80%

3 × continuous green light 40–60%

2 × continuous green light 20–40%

1 × continuous green light 5–20%

1 × flashing green light 0–5%

Recommendations for Optimal Handling of the

Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Assembly

u Before carrying out any work on the power tool (e.g.

maintenance, tool change etc.), remove the battery

from the power tool. There is risk of injury from uninten-

tionally pressing the on/off switch.

u Before inserting the rechargeable battery into the

power tool, always ensure that the release switch(14)

is working properly and returns to the OFF position

when it is released.

Fitting the Cutting Jaws (seefiguresA−E)

Always fit the cutting jaws(3) in the correct orientation and

make sure they are properly secured. If the cutting jaws are

not attached correctly or they are attached loosely, this

could cause a break in the cutting jaws, which could lead to

personal injury from fragments being flung out

(seefigureA).

Remove any burrs from the cutting jaws with a file(3).

Always use a pair of cutting jaws(3). This consists of one

cutting jaw marked with a dot and one cutting jaw marked

with two dots (seefigureD). The pair of cutting jaws can be

replaced between the moving holder(2) and the stationary

holder(4).

Check whether the holders(2) and(4) for the cutting

jaws(3) are fully open. If this is not the case, insert the re-

chargeable battery and press the release switch(14) until

the holders are fully open. Remove the battery again.

Set the selector switch(13) to the locking position

(seefigureC).

Unscrew the screws(18) using the hex key(8) provided.

Insert the cutting jaws(3) into the holders(2) and(4) in the

correct position. Secure the cutting jaws(3) again with the

screws(18).

Note: The pair of cutting jaws(3) can only be screwed to-

gether in the power tool if the labelled end surfaces are fa-

cing each other. The cutting jaws must be oriented according

to the thread size to be cut (seefigureD).

Operation

u Replace the cutting jaws(3) if the cutting edges are

chipped or deformed (seefigure E). Refer to the fur-

ther instructions(see "Replacing the Cutting Jaws",

page23).

u The cutting jaws(3) are extremely sharp. You should

therefore always keep your hands away from cutting

edges and moving parts. Do not cut short workpiece

parts where your hands could get close to the cutting

jaws. There is a risk of serious injury or of limbs being

severed.

u Make sure that cutting jaws(3) of the correct size are

fitted to the power tool and that both cutting jaws are

oriented in the correct position. Before you start cut-

ting, check the thread size printed on the cutting jaws.

u Before pressing the release switch(14), insert the

threaded rod such that its screw threads match those

of the stationary cutting jaw. If the screw threads are

not aligned correctly, this could cause a break in the

cutting jaws and cause personal injury from fragments

being flung out.

Attaching the Fall Protection System

(seefigureB)

Note: A fall protection system(22) that is suitable for the

weight of the entire system should be used to prevent the

power tool from falling. The maximum permitted length of

the fall protection system is1.1 m. Please always refer to the

permitted attachment area(21) on the power tool.

It is best to use the fall protection system with a tape loop se-

cured by an anchor knot or a fall protection system with fall

damper.

Please always refer to the operating instructions when at-

taching the fall protection system(22).

u Always secure the opposite side of the fall protection

system to a stable structure (e.g. a building or scaf-

folding) and never to the user.

The fall protection system must be able to move freely

and may only be attached to the power tool at the

fixed anchorage point(23) and in the permitted at-

Bosch Power Tools 1 609 92A A3L | (17.03.2025)

/ 267

Bekijk gratis de handleiding van Bosch GGC 18V-12 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.