Bosch GGC 18V-12 Professional handleiding

Niet gecategoriseerd

Bosch

267 pagina's

PDF beschikbaar

Handleiding

/ 267

Je bekijkt pagina 22 van 267

22 | English

tachment area(21) .

Select the fixed anchorage point (23) such that the

power tool can fall freely into the fall protection sys-

tem without wrapping around or putting the user at

risk of harm in the event of a fall.

Place the sling of the fall protection system(22) through the

handle(17) and guide the end with the karabiner through

the sling. When tightening the sling, ensure that it is cor-

rectly laid the attachment area(21) and that it has not twis-

ted over itself. Inspect the fall protection system before

every use and check that is correctly secured to the power

tool and the anchorage point(23).

Starting Operation

Selector Switch (seefigureC)

u Always set the selector switch(13) to the locking pos-

ition when you are not using the power tool.

u Before starting to operate the power tool, always en-

sure that the selector switch(13)is in the correct posi-

tion.

u Do not move the selector switch(13) when the re-

lease switch(14) is pressed. This may damage the

power tool.

To start cutting mode, set the (13) selector switch to the

cutting position (position a, ) and press the release

switch (14). To reverse the direction of movement, set the

selector switch(13) to the reversal position (position b )

and press and hold the selector switch in this position while

pressing the release switch. When you release the selector

switch and the release switch, the power tool will automatic-

ally switch to the locking position . If you press the release

switch(14) continuously, the power tool will go through a

full cycle and automatically stop in the fully open position. To

lock the release switch(14), set the selector switch(13) to

the locking position . When in this position, the release

switch(14) cannot be pressed.

Note: Do not cut threaded rods while the direction of move-

ment is reversed. This will lead to the power tool being dam-

aged. Only operate the power tool in the reverse direction of

movement with no load or in order to fully open the cutting

jaws(3).

Note: If you release the release switch(14) after cutting

while the cutting jaws(3) are opening and also set the se-

lector switch(13) to the reversal position, the cutting jaws

will close. They will open again if you press the release

switch again.

Switching On and Off

Adjust the thread size of the threaded rod to be cut on the

threaded rod guide(5). This moves the M6/M8 and M10/

M12 supporting surface for the threaded rod to the correct

orientation.

Before pressing the release switch(14), insert the threaded

rod such that its screw threads match those of the cutting

jaw(3) of the stationary holder(4). If the screw threads are

not aligned correctly, this could lead to a break in the cutting

jaws(3) and cause personal injury from fragments being

flung out. This could also damage the thread of the threaded

rod such that you can no longer screw on any nuts.

Before cutting, position the threaded rode at a right angle to

the cutting line(19) (seefigureG) and ensure that the

threaded rod is in good contact with the previously adjusted

rod guide.

To start cutting mode, ensure that the selector switch(13)

is in the cutting position (position a , seefigureC) and

press the release switch(14) continuously. The cutting jaw

on the moving holder(2) overlaps with the cutting jaw on the

stationary holder(4) and then moves back. If you release the

release switch(14) before completing the cut, the cutting

jaws(3) will come to a stop.

Note: If you are cutting a threaded rod made from ductile

metal, such as stainless steel, burrs may be generated at the

end of the cut. In this case, remove the burrs with a file.

Auto-Stop Function

If you press the release switch(14) continuously, the

holders(2) and(4) of the cutting jaws(3) will close once,

before returning to the fully open position and then coming

to a stop. Release the release switch(14) and press it again

to start the next cutting sequence.

Storing the Hex Key

The hex key(8) provided can be stored on the power tool so

that it is not lost. To take out the hex key, remove the re-

chargeable battery and pull out the hex key. After use, stow

the hex key back in the power tool and insert the re-

chargeable battery.

Worklight

The worklight(16) illuminates the work area in poor lighting

conditions.

Caution: Do not look directly into the lamp.

Press the release switch(14) gently to switch on the

worklight(16) without also switching on the motor. Fully

press the release switch if you wish to cut threaded rods.

The worklight is automatically switched on during operation.

The lamp will light up for as long as the release switch is

pressed. The worklight will go out approximately 15seconds

after the release switch is released.

Threaded Rod Guide (seefiguresF−G)

To make precise cuts, move the threaded rod guide (5) into

position depending on the diameter of the threaded rod to

be cut (M6/M8 or M10/M12).

Before cutting, position the threaded rod perpendicular to

the cutting line(19). Make sure that the threads of the

threaded rod and the threads of the stationary cutting jaw

are interlinked (seefigureK). Make sure that the threaded

rod is in good contact with both surfaces of the rod guide

(seefigureG) and hold the threaded rod in this position with

a firm grip. The cutting process generates a reactive force

that can tip over the threaded rod. If the threaded rod tips

over, this can lead to a poor cutting quality, the threaded rod

jamming, or damage to the cutting jaws or the threaded rod.

You should therefore keep the threaded rod in the described

orientation while cutting.

1 609 92A A3L | (17.03.2025) Bosch Power Tools

/ 267

Bekijk gratis de handleiding van Bosch GGC 18V-12 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.