Bosch GFP 18V-10 Professional handleiding

Niet gecategoriseerd

Bosch

291 pagina's

PDF beschikbaar

Handleiding

/ 291

Je bekijkt pagina 21 van 291

English | 21

– If you always connect the grease cylinder to a low-pres-

sure pump for filling, you can leave the filling valve

screwed into the power tool.

Otherwise, unscrew the filling valve from the power tool

and close the thread again with the screw plug(30).

– Bleed the system (see "Bleeding (seefigureI)",

page21).

Bleeding (seefigureI)

Bleeding via the bleed valve

– To bleed the grease cylinder(12) or the inserted cart-

ridges, press the bleed valve(14) until grease is escaping

continuously.

During bleeding, you can also press the on/off switch(6).

Active bleeding

– Lock the spring rod(23) by turning it 90° with the grease

slider(25). Press on the bleed valve(14) and push the

spring rod forwards until grease escapes from the

nosepiece of the hose(19).

Press on the bleed valve(14) and push the base of the in-

serted cartridge (Reiner or Lube Shuttle type) forwards

using a suitable object until grease escapes from the

nosepiece of the hose(19).

Installing the 90° nosepiece (seefigureJ)

For lubrication points that are difficult to access, a

nosepiece angled by 90°(32) can be installed on the normal

nosepiece(31).

– Insert the 90° nosepiece(32) into the normal

nosepiece(31) on the hose(19) and push the

sleeve(33) over the connection.

– To remove the 90° nosepiece(32), push back the

sleeve(33) and pull the 90° nosepiece(32) out of the

nosepiece(31).

Replacing the protective housing for the

rechargeable battery

If the protective housing for the rechargeable battery(8) has

been damaged, it must be replaced.

– Remove the rechargeable battery(9).

– Loosen the screws(11) and remove the damaged pro-

tective housing for the rechargeable battery.

– Screw the new protective housing for the rechargeable

battery back on.

Operation

Work preparation

Setting the number of pump strokes

By preselecting the pump strokes, a constant grease quant-

ity can be applied to various lubrication points.

– Set the required number of pump strokes on the

thumbwheel(2).

Thumbwheel(2) Number of pump strokes

Unlimited as long as the on/off

switch(6) is pressed.

1 ... 50

Once the set number of pump strokes

has been reached, the power tool

switches off automatically, even if the

on/off switch(6) continues to be

pressed.

Setting the gear

The power tool has two gears that regulate the grease flow

rate in relation to the working pressure.

– Set the required gear using the switch(7).

Switch(7) Grease quantity/working pressure

First gear

– Grease flow rate: 100 g/min

– Maximum working pressure:

10000psi

Second gear

– Maximum grease flow rate: 320 g/min

– Working pressure: 6000−8000psi

Overview of grease quantities

Different grease quantities are applied depending on the

number of pump strokes.

Number of pump strokes Grease quantity

[g]

0.7

1.4

2.1

2.8

3.5

4.2

4.9

5.6

6.3

7.0

10.5

14.0

17.5

35.0

A) ±5 %

Starting operation

Switching on and off

– To unlock the on/off switch(6), press the locking

mechanism(4) from left to right.

– To start the power tool, press and hold the on/off switch

(6).

– With the on/off switch pressed, press the lock-on

button(5) to lock the on/off switch(6) in this position.

– To switch off the power tool, release the on/off switch

(6); or, if the switch is locked with the lock-on button (5),

briefly press the on/off switch (6) and then release it.

Bosch Power Tools 1 609 92A 9T8 | (17.03.2025)

/ 291

Bekijk gratis de handleiding van Bosch GFP 18V-10 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.