Bosch GFP 18V-10 Professional handleiding

Niet gecategoriseerd

Bosch

291 pagina's

PDF beschikbaar

Handleiding

/ 291

Je bekijkt pagina 20 van 291

20 | English

Installing the shoulder strap (seefigureA)

During work, you can hang the power tool across your

shoulder using the shoulder strap(20).

– Hook the shoulder strap(20) into the brackets(15).

Changing the hose (seefigureB)

The product is supplied with a hose(19) with a length of

120cm already fitted.

Replace any kinked or damaged hoses.

– Loosen the nut(21) on the hose using a commercially

available wrench and unscrew the installed hose(19)

from the power tool.

– Screw the new hose(19) into the power tool and then

tighten the nut(21) to a tightening torque of 13–16Nm.

Converting hose brackets (seefigureC)

The hose brackets(13) can be flexibly positioned on the

power tool.

– Detach the hose(19) from the hose bracket(13).

– Loosen the screws(22) and pull the hose brackets out of

the housing.

– Depending on your preferred work posture, insert the

hose bracket into the recesses provided and tighten it

again.

Filling the power tool with grease

Permissible cartridges

– Pull-off cartridges (400g)

– Reiner type screw-in cartridge (500g)

(can be used with adapter(28): 2608001205 )

– Lube Shuttle screw-in cartridge (400g)

(can be used with adapter(29): 2608001204 )

Inserting the pull-off cartridge (seefiguresD1−D2)

– Unscrew the grease cylinder(12) from the power tool by

turning it anticlockwise.

– Pull the spring rod(23) on the retractor(16) all the way

out and lock it in the safety groove(24).

– Remove the cap from the pull-off cartridge and insert the

cartridge into the grease cylinder(12) with the open side

facing down.

– Only now should you tear off the pull-off closure of the

cartridge.

– Screw the grease cylinder(12) into the power tool by

turning it clockwise.

– Release the spring rod(23) from the safety groove(24)

and slowly press the spring rod into the grease

cylinder(12) as far as it will go.

Release the spring rod(23) from the safety groove(24)

and lock the spring rod by rotating 90° with the grease

pusher(25). As the grease flows out from the front, the

spring rod is pulled from the back, and the remaining

quantity can be read off the scale of the spring rod

(seefigureD3).

– Bleed the system (see "Bleeding (seefigureI)",

page21).

Inserting a Reiner type cartridge (seefiguresE1−E3)

– Unscrew the grease cylinder(12) from the power tool by

turning it anticlockwise.

– Press the retaining springs(26) together and pull the

reducer(27) out of the housing.

– Screw the adapter(28) into the power tool and tighten it

with a wrench (width across flats 30mm).

– Screw a Reiner type cartridge into the adapter(28).

– Bleed the system (see "Bleeding (seefigureI)",

page21).

Inserting a Lube Shuttle Type Cartridge

(seefiguresF1−F2)

– Unscrew the grease cylinder(12) from the power tool by

turning it anticlockwise.

– If necessary, reinsert the reducer(27) into the housing.

– Screw the adapter(29) into the power tool and tighten it

with a wrench (width across flats 41mm).

– Screw a Lube shuttle type cartridge into the

adapter(29).

– Bleed the system (see "Bleeding (seefigureI)",

page21).

Filling the grease cylinder from containers (seefigureG)

– Unscrew the grease cylinder(12) from the power tool by

turning it anticlockwise.

– Immerse the grease cylinder approx. 5cm in the grease

from the container.

– Slowly pull the spring rod(23) on the retractor(16) all

the way out and lock it in the safety groove(24).

– Screw the grease cylinder(12) into the power tool by

turning it clockwise.

– Release the spring rod(23) from the safety groove(24)

and slowly press the spring rod into the grease

cylinder(12) as far as it will go.

Release the spring rod(23) from the safety groove(24)

and lock the spring rod by rotating 90° with the grease

pusher(25). As the grease flows out from the front, the

spring rod is pulled from the back, and the remaining

quantity can be read off the scale of the spring rod

(seefigureD3).

– Bleed the system (see "Bleeding (seefigureI)",

page21).

Filling the grease cylinder using the filling pump

(seefiguresH1−H2)

Using a low-pressure pump, the grease cylinder(12) can be

filled directly from a grease barrel via a filling valve (1/8"

NPT thread).

– Remove the screw plug(30) using a commercially avail-

able hex key, and screw the filling valve (component of

the low-pressure pump) into the thread.

– Connect the low-pressure pump to the filling valve and fill

the grease cylinder(12).

1 609 92A 9T8 | (17.03.2025) Bosch Power Tools

/ 291

Bekijk gratis de handleiding van Bosch GFP 18V-10 Professional, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.