Handleiding
Je bekijkt pagina 28 van 56
Functions and operation
EN
28 bora.com
Protect your hands when the appliance is hot by using oven
gloves or pot holders. Only use dry gloves or pot holders. Wet
or damp fabrics conduct heat more easily and can cause
steam burns. Ensure that these fabrics do not get too close to
the flames. Do not use oversized pot holders, tea towels or
similar.
Grease splashes and other flammable (food) residues on the
cooktop can catch fire. Remove them as soon as possible.
For maximum performance with minimum gas
consumption, we recommend that you:
u
use cookware with a base that covers the flame entirely so that
this does not burn beyond the base;
u
use suitable pans on each gas burner;
u
position the cookware centrally on the gas hob;
u
set the gas burner to the lowest power level (small flame) once the
pan contents are simmering;
u
adjust the power level of the cooktop extractor to the power level
of the gas cooktop.
Using the gas cooktop with a cooktop extractor:
If the gas cooktop is used together with a cooktop extractor, the
airflow of the extractor can affect the gas flame.
u
Avoid using a high power level on the cooktop extractor when the
gas cooktop is set to a low power level.
u
If necessary, reduce the power level on the cooktop extractor
when you turn on the gas cooktop.
u
Do not use the gas cooktop without cookware. The gas flame is
protected from the airflow of the cooktop extractor by the
geometry of the pan supports and the cookware.
u
If necessary, reduce the power level on the cooktop extractor to
improve heat input or distribution.
Flames can set fire to or damage the grease filter in the
cooktop extractor and the air-channelling components. Never
flambé food when using a cooktop extractor.
The performance characteristics of the gas cooktop (e.g.
heating times, efficiency, etc.) are affected by the cooktop
extractor. The cooktop extractor also affects the heat input
and distribution.
In recirculation mode the recirculated air affects the gas
cooktop. If the gas flame goes out, is excessively affected by
the extractor and/or the flame is not as it should be (e.g. soot
production, flame blowback, etc.), the return flow aperture
must be enlarged.
5.5.4
Setting cooking zone power levels
The power levels are controlled by turning the knob ring to the
desired power level (electronic power adjustment).
Increasing the power level
u
Turning the knob ring clockwise
Reducing the power level
u
Turning the knob ring anticlockwise
T
The selected power level is shown in the display on the extractor
control knob.
Fig.5.25
Setting cooking zone power levels
Setting the temperature on the Tepan stainless steel grill
u
Turn the knob ring to the desired temperature.
T
The control knob display shows the target temperature for 3
seconds. Then the warm-up phase begins.
T
During the warm-up phase, the corresponding cooking zone display
flashes and the current temperature is shown.
T
As soon as the target temperature is reached, the warm-up phase
comes to an end and the target temperature is continuously
displayed.
5.5.5
Cooktop power setting
When the power setting is activated, maximum cooking zone power is
available for a predefined time. The available power is targeted at the
cooking zone, meaning that the max. power of the second cooking
zone is automatically reduced temporarily.
Activating the power setting for a cooking zone
u
Turn the knob ring clockwise to power setting P.
T
After 10 minutes, the power setting is automatically switched back
to power level 9 (20 minutes on the gas cooktop).
T
The power setting cannot be activated if the bridging function is
switched on
T
If one cooking zone is operated on the power setting, the second
cooking zone can be operated at a maximum power level of 5.
T
On the cooktop PKCH3 the power setting corresponds to the
Hyper setting.
Never heat up oil, fat and the like on the power setting. The
bottom of the pan can overheat due to the high power output.
Activating the power setting on the Tepan stainless steel
grill
u
Turn the knob ring clockwise to temperature 240/250°C (= power
setting).
T
After 10 minutes, the power setting is automatically switched back
to power level 9 (230°C).
T
On the Tepan stainless steel grill, both cooking zones can be
operated on the power setting at the same time, even with the
bridging function.
Deactivating the power setting
the power setting is deactivated early if another power level is set.
5.5.6
Bridging function
With the bridging function two cooking zones can be combined to
form one large cooking zone. The power for the combined zones is
then adjusted by a single operating control. Power adjustment takes
place simultaneously (both cooking zones are operated on the same
power level). The bridging function is suitable for heating food, e.g. in
a roaster.
Bekijk gratis de handleiding van Bora PKCB3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Bora |
| Model | PKCB3 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 10414 MB |
