Bartscher 155660 handleiding

Fornuis

Bartscher

16 pagina's

PDF beschikbaar

Handleiding

LEVELLING

Once the supplied feet are tted and screwed in, if necessary, level the appliance by turning them. This will avoid any possible oscillation.

CONNECTION

GAS CONNECTION

While

the connection to the gas mains or gas cylinder can be made with various types of tubes (exible rubber or steel), it is nevertheless necessary to

carry out this operation in accordance with regulations and amendments in force, once it has been ascertained that the appliance is properly adjusted to

the type of gas it will be supplied with (see technical plate inside the bottom door or on the rear of the cooker).

CONNECTION WITH FLEXIBLE METAL TUBE (g. 15 - page 13)

The connection is made using a tube that is compliant with national regulation, connected to the appliance threaded tting, through the use of a sealing

joint (gasket). The maximum extension of the tube must not exceed 2 metres in length.

CONNECTION WITH FLEXIBLE RUBBER TUBE

This type of connection is not authorized when the appliance is recessed (class 2/1 appliance) and the tube can not be inspected for its entire length.

Connect the tube connection to the threaded tting through the use of a sealing joint (washer).

Depending on the type of gas being used, the tubes will have different diameters:

• G30 (GPL) gas tube (g. 16 - page 13) to be applied to tube connections with an 8 mm diameter;

• G20 (METHANE) gas tube (g. 17 - page 13) to be applied to tube connections with a 12 mm diameter.

Fasten the two ends of the tube with the required tube clamps according to national regulations.

The tube must be replaced by the terms of the date printed on it and must not exceed the maximum length of 1.5 metres.

The tube must not come into contact with sharp objects and corners; it must not be strained or twisted; no point of the tube must exceed a temperature

of 50°C.

GAS CONNECTION TO THE CYLINDER

With models with a cylinder cabinet it is possible to house cylinders with up to 15 kg of butane, that are compliant with national regulations.

The cylinder must be equipped with a pressure reducer, compliant with national regulations.

The connection to the cylinder must be set up in compliance with installation standards pursuant to national regulations.

The exible tube used for the connection must have an internal diameter of 8 mm, it must be compliant with standards and must be replaced before its

expiration date. It must be tted to the tube connection on the cooker and the pressure reducer using regulation tube clamps.

During the operations to connect the cylinder, it is necessary to follow the instructions below:

• the gas connecting tube must not exceed 1 meter in length;

• the pressure reducer tting must face the door of the cylinder cabinet;

• the route of the exible tube must not touch any hot surfaces of the cooker (the left inside wall of the cylinder cabinet, the rear of the cooker and cabinet

ceiling) and IT MUST follow the route provided by the relative clamps;

• the cylinder must be set up so that it is not touching the wall adjacent to the oven.

Whenever you nish cooking, it is advisable to close the cylinder valve.

CONNECTION WITH RIGID COPPER PIPE

(g. 18 - page 13)

Connect the rigid part to the threaded tting located on the rear side of the appliance, through a regulation sealing joint.

SEAL CHECK

Following installation, make sure the ttings are rmly connected. Never use a ame to check the seal on the gas circuits, always use a soapy solution.

ELECTRICAL CONNECTION

Install a plug on the cable, suitable for the load stated on the specications plate on the appliance (located inside the door under the over door, or on the

rear of the cooker).

The electrical connection must have an efcient earthing connection. The yellow-green conductor for the power cable must not have any switches set up

along it.

When there is a direct connection to the mains, it is necessary to set up a omnipolar switch between the appliance and the mains with a minimum opening

between the contacts of 3 mm, sized for the load and compliant with national standards in force (the earth wire must not have any switches set up along

it). The power cable must be positioned so that it does not exceed the ambient temperature by 50°C at any point.

The manufacturing company will not be held liable in cases of failure to observe the electrical regulations in force, and if the connection has not been set

up by qualied personnel.

g. Cg. B

g. A

If the gas pipe is damaged, do not attempt to repair it by yourself but replace it with a new one before using the appliance.

Cooker with 90 x 60 cylinder cabinet Cooker with 80 x 50 cylinder cabinet

CENTRE DISTANCE OF COOKER CENTRE DISTANCE OF COOKER

BRACKET 1

BRACKET 2

BRACKET 1

BRACKET 2

200 mm 315/320 mm 200 mm 310 mm

Cooker with 80 x 50 cabinet

CENTRE DISTANCE OF COOKER

BRACKET 1

BRACKET 2

280 mm

Bekijk gratis de handleiding van Bartscher 155660, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.