Bartscher 155660 handleiding

Fornuis

Bartscher

16 pagina's

PDF beschikbaar

Handleiding

g.15 g.16 g.17 g.18

ADAPTATION TO THE DIFFERENT TYPES OF GAS

WARNING

The appliance is designed to operate with different types of gas; each type of gas requires specic injectors and adjustments. To make

any variations it is always necessary to cut the appliance off from the power mains and temporarily cut off the gas supply from the mains.

CHANGING HOB BURNER INJECTORS (g. 19)

Manually remove the burners (no other disassembly operation is required) and using a suitable socket wrench, unscrew the injectors and replace them with

the ones suitable for the type of gas, as listed in the technical data table and in the data plate on the cooker (see gure at the top of page 12).

REGULATING THE MINIMUM FLOW LEVEL OF GAS TO THE HOB BURNERS

(g. 20)

The regulation of the minimum ow rate of gas to the burners is carried out in factory. When an injector is changed to adapt it to the type of gas available, or

following particular pressure conditions of the mains, it may be necessary to regulate the minimum again. Ignite the burner and let it operate on maximum

capacity for approximately 10 minutes. Rotate the knob to the minimum position. Remove the knob by pulling it off the valve rod. With a small at head

screwdriver adjust the minimum by turning the by-pass screw clockwise to decrease the ame or counter-clockwise to increase the ame. When using

valve cocks the adjustment screw (by-pass) is located on the body of the cock. When using valves other than valve cocks, the adjustment screw is situated

inside the valve body. After any injectors replacement or adjustment operation always make sure that the ame is blue, steady and quiet and produces no

detachment from the burner and will not cause backre between the passage from maximum to minimum.

CHANGING BURNER INJECTORS INSIDE THE OVEN (g. 22)

Take the burners out by removing the clamping screws and using a suitable wrench to unscrew the injectors and replace them with the ones that are

suitable for the type of gas, as listed in the technical data table.

REGULATING PRIMARY BURNER AIR INSIDE THE OVEN (only applicable to models with tube burners)

REGULATING THE MINIMUM FLOW RATE OF GAS TO THE OVEN AND GRILL BURNERS (g. 23)

Turn the burner on and position the knob on the maximum temperature. L Rotate the knob to the minimum

position. Pull the knob out of the thermostat rod and with a small at head screwdriver adjust the minimum by turning the by-pass screw clockwise to

decrease the ame or counter-clockwise to increase the ame. The ame should be short and steady; no air drafts or the closing of the door have to

cause the extinguishing of the ame or its return. The adjusting screw (by-pass) is usually located on the body of the thermostat. When using valve cocks

the adjustment screw (by-pass) is situated on the body of the cock (g. 23). When using valves other than valve cocks, the adjustment screw is situated

inside the valve body.

After any action to change or adjust parts of the appliance, it is necessary to carefully re-assemble all affected parts to restore the original features. Any

adaptations made for a different type of gas must be completed by changing the tube connection. In this case, also check the circuit seal with a soapy

solution, and never with the use of a ame. Lastly, replace the old calibration label with a new one (included) for the new type of gas being used.

Your product is now correctly installed. Please remove all information labels and materials (located inside the oven) before turning it on.

g.19

g.22 g.23

g.20

Some models have a metal collar (xed with screw) located on the end of the burner to adjust the air opening (by increasing or decreasing the amount of air) based

on the result you wish to obtain. After any injector adjustment operation always make sure that the ame is blue, steady and quiet and produces no detachment

from the back burner and will not cause backre between the passage from maximum to minimum.

et the oven heat up for at least 30 minutes.

Bekijk gratis de handleiding van Bartscher 155660, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.