Axxess AXLOC4M-150 handleiding
Handleiding
Je bekijkt pagina 1 van 2
AXLOC4M-150 AXLOC4M-150
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
AXLOC4M-150 AXLOC4M-150
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
REV. 12/13/19 REV. 12/13/19© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION
Integrate • AxxessInterfaces.com Integrate • AxxessInterfaces.com
REV. 12/13/19 REV. 12/13/19© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION
Integrate • AxxessInterfaces.com Integrate • AxxessInterfaces.com
A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.
The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line
level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add
aftermarket amplifiers. This device will also detect the presence of an audio signal and then
generate a +12V output that can be used to turn-on an aftermarket amplifier.
Features and specifications
The LOC is able to handle 150 watts per channel continuous input without over heating.
The input circuitry is designed to correct the crossover distortion commonly found on
standard LOCs while providing a high to low level step down of 6:1. Output audio level is
infinitely adjustable using the onboard, high quality potentiometers. The remote output
or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if
additional current is needed. The remote output will trigger instantaneously when the LOC
detects a DC voltage on the white, left + audio input wire above 5V or a very low audio
signal. It will shut off 60 seconds after no signal is detected.
Installation
The LOC should be installed on a stereo’s speaker output wires or the output wires on an
OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo
in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM
speakers. Please refer to the wiring diagram for the input connection details.
Continued on next page
A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.
The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line
level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add
aftermarket amplifiers. This device will also detect the presence of an audio signal and then
generate a +12V output that can be used to turn-on an aftermarket amplifier.
Features and specifications
The LOC is able to handle 150 watts per channel continuous input without over heating.
The input circuitry is designed to correct the crossover distortion commonly found on
standard LOCs while providing a high to low level step down of 6:1. Output audio level is
infinitely adjustable using the onboard, high quality potentiometers. The remote output
or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if
additional current is needed. The remote output will trigger instantaneously when the LOC
detects a DC voltage on the white, left + audio input wire above 5V or a very low audio
signal. It will shut off 60 seconds after no signal is detected.
Installation
The LOC should be installed on a stereo’s speaker output wires or the output wires on an
OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo
in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM
speakers. Please refer to the wiring diagram for the input connection details.
Continued on next page
A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.
The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line
level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add
aftermarket amplifiers. This device will also detect the presence of an audio signal and then
generate a +12V output that can be used to turn-on an aftermarket amplifier.
Features and specifications
The LOC is able to handle 150 watts per channel continuous input without over heating. The
input circuitry is designed to correct the crossover distortion commonly found on standard
LOCs while providing a high to low level step down of 6:1. Output audio level is infinitely
adjustable using the onboard, high quality potentiometers. The remote output or amplifier
trigger is rated at 500mA (+12V) and will easily handle an outboard relay if additional
current is needed. The remote output will trigger instantaneously when the LOC detects a
DC voltage on the white, left + audio input wire above 5V or a very low audio signal. It will
shut off 60 seconds after no signal is detected.
Installation
The LOC should be installed on a stereo’s speaker output wires or the output wires on an
OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo
in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM
speakers. Please refer to the wiring diagram for the input connection details.
Continued on next page
A 4 Channel Adjustable, Line Output Converter (LOC) with Built-in Amplifier Remote Generator.
The LOC is designed to convert (4) channels of speaker level audio into (4) channels of line
level audio that can be used by OEM amplifiers. It can also be used with OEM radios to add
aftermarket amplifiers. This device will also detect the presence of an audio signal and then
generate a +12V output that can be used to turn-on an aftermarket amplifier.
Features and specifications
The LOC is able to handle 150 watts per channel continuous input without over heating.
The input circuitry is designed to correct the crossover distortion commonly found on
standard LOCs while providing a high to low level step down of 6:1. Output audio level is
infinitely adjustable using the onboard, high quality potentiometers. The remote output
or amplifier trigger is rated at 500mA (+12V) and will easily handle an outboard relay if
additional current is needed. The remote output will trigger instantaneously when the LOC
detects a DC voltage on the white, left + audio input wire above 5V or a very low audio
signal. It will shut off 60 seconds after no signal is detected.
Installation
The LOC should be installed on a stereo’s speaker output wires or the output wires on an
OEM amplifier of up to 150 watts per channel. These wires can be found behind the stereo
in the dash, on the output of an OEM amplifier, or on the input terminals on the OEM
speakers. Please refer to the wiring diagram for the input connection details.
Continued on next page
Bekijk gratis de handleiding van Axxess AXLOC4M-150, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Axxess |
| Model | AXLOC4M-150 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 217 MB |
