Axxess AX-LOC4.4-PRO handleiding
Handleiding
Je bekijkt pagina 5 van 12
5
REV. 5/8/23 INSTAX-LOC2.2PRO/AX-LOC2.4PRO/AX-LOC4.4PRO
FEATURE BREAKDOWNS
Turn On Signal
Audio Sense – When selected the LOC will power up when an audio signal is present regardless
of source. If the radio is muted and the LOC doesn’t see an audio signal it will turn off.
DC Signal Sense (Default) – Detects when the OE radio or OE amplifier turns on. The AX-LOC2.2PRO,
AX-LOC2.4PRO and AX-LOC4.4PRO detects the DC voltage across the speaker leads and will
provide 12 volts to the REM OUT.
REM IN – This is the standard way to turn of aftermarket equipment by using a dedicated
amp turn on signal or a true ignition signal. When the REM IN is powered it will output
through the REM Out.
Ground Isolation Settings – Different types of ground noise can easily enter into your audio
system. The Ground Isolation Switch on the LOC will help eliminate some of the most common
ground noises with the simple flip of a switch.
GND – The ground for the LOC is tied to the ground shield of the audio signal.
ISO – The ground of the LOC and ground shield of the RCA are separated.
200 Ohm – LOC ground and ground shield of RCAs are connected to each other by a 200
ohm resistor, balancing yet isolating the ground circuit.
Load Select Settings – Factory radios and amplifiers can sometimes stop passing audio when
they do not see the original speaker’s impedance. This is a common issue found in many
Chrysler vehicles. The load selector switch will offer two Ohm Load settings that will make the
factory equipment think the original speakers are still connected and start passing audio. In some
Chrysler vehicles you will need to let the vehicle go the sleep (turn ignition off for 2 minutes)
after each load selection.
20 Ohm – Commonly used in vehicles that do not have a factory amplifier. Mainly late
model Chrysler vehicles, which includes RAM, JEEP, DODGE, and some FIATS
60 Ohm – Commonly used in vehicles with a factory amplifier. Mainly late model Chrysler
vehicles, which includes RAM, JEEP, DODGE, and some FIATS
20k Ohm – Default setting and used for all other applications.
If none of these Ohm load settings restore the factory audio or if you have distortion, Axxess
offers additional load resistors that plug directly into the speaker level input terminal(s) of each
LOC. AX-LR39 is the only value not built into the Axxess LOCs.
Boost Adjustment – Works only when the LPS is switched on. This adjustment increases the
output levels at 45Hz. Offers a +12dB increase for the rear channels only.
LPF – Low Pass Filter, when ON this will allow the LOC to pass low frequencies from 250Hz and
below from the rear channels of the LOC. When OFF full frequency range will pass through the
REAR OUTPUT.
For AX-LOC4.4-PRO Only: Input Mode – AX-LOC4.4-PRO offers the ability to have two channels
of speaker level input or all four speakers. In applications where you one have two channels of
input, select 2CH mode. The audio signal will pass through both the FRONT and REAR OUTPUTS.
Having four channels of input would help retain OE features like Fade from the factory radio.
Bekijk gratis de handleiding van Axxess AX-LOC4.4-PRO, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Axxess |
| Model | AX-LOC4.4-PRO |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1271 MB |
