Atlas Sound Texas Tough TT35-35V handleiding

Niet gecategoriseerd

Atlas Sound

15 pagina's

PDF beschikbaar

Handleiding

All other Trademarks are property of their respective owners. No endorsement is implied. Due to continual product development, specifications are subject to change without notice. ATS005957 RevD 4/21 P/N 492378

AtlasIED.com

TELEPHONE: (800) 876-3333

SUPPORT@ATLASIED.COM

1601 JACK MCKAY BLVD.

ENNIS, TEXAS 75119 U.S.A.

Initial Rail Setup

1. Remove metal shipping stiffeners (if included) using a #2 Phillips

screwdriver by removing the (4) 10-32 Phillips cross-drive screws.

2. Adjustable rails may move forward and backward within the hat-section

slot. Once relocated to the desired position the rails lock in place with

AtlasIED’s DINlok™ System Technology.

3. Locate front rails in the front-to-back direction as required by equipment

to be installed. Once located, be sure to leave an equal gap at the top

and bottom of each rail as required to clear any mounting hardware.

NOTE: While front rails are typically mounted at the front of the cabinet,

closest to the front door, this position may not provide adequate clearance

when front door is closed. Always consider the forward space for knobs,

connections, etc. as required by the installed components.

4. If moving rear rack rails, use a tape measure to locate rear rail with

respect to the front rail surface. This distance will vary based on installed

equipment. Again, be sure to leave an equal gap at the top and bottom

of each rail to clear any mounting hardware.

NOTE: Verify rear door / lock will not interfere with installed equipment.

5. Once relocated to the desired position the rails lock in place using

AtlasIED’s DINlok™ System Technology.

Initial Rear Door Setup

DID YOU KNOW? The rear flush door may be hung left- or right-hinged as

required by the final installation.

NOTE: The flush rear door may not be installed on the front of the cabinet.

NOTE: Installed equipment may interfere with proper door closing. See

Initial Rail Setup section before proceeding.

1. Remove rear door by pulling the spring-loaded Cane Bolts towards the

center of the door.

2. Be sure nylon gap washer located at the bottom of the door is retained.

3. Flip door as required.

4. Install the door into position with the nylon gap washer located at the

bottom of the door.

5. Be sure spring-loaded Cane Bolts actuate to their outward position.

To Remove

1. Required Tooling:

a. Razor Knife

b. #2 Philips Cross-Drive Screw Driver (Manual or Auto)

c. 3/8” Hex Socket Driver

d. Tape Measure (optional)

2. Shipping Packaging Removable:

a. Carefully cut and remove shipping straps holding cabinet to shipping pallet.

b. Remove shrink plastic and shipping materials.

c. Remove metal shipping stiffeners (up to 2 per cabinet depending on model) by removing the (4) 10-32 philips cross-drive

screws. Use a #2 philips screwdriver for this task.

NOTE: Shipping stiffeners are actually a standard 3RU panel; therefore, may be used to help close the top of

the cabinet. Additional panels will be required to fully close the surface.

d. Carefully cut and remove the hardware bag containing door keys, rack rail hardware, top hardware. Keep for future use.

3. Cabinet Orientation:

a. The front of the cabinet is denoted by the presence of the Atlas Sound

Logo plug (top left on most models)

NOTE: Logo may be removed and replaced by M-1A IR

Repeater in cases where a door blocks IR remote control

signals.

b. Bottom of the cabinet will contain mounting points for casters.

Initial Rail Setup:

NOTE: 100 Series cabinets do not require any adjustments;

therefore, 100 Series users may skip this section.

Logo Plug

Shipping

Stiffener

Caster Mount

Holes

a. Adjustable rails may move forward and backward within the hat-section

slot. In addition, there is some adjustment up and down. Once rails are

located as required, use 3/8” hex socket driver to torque into place.

Recommended torque: 82 ± 2 in-lbs

b. Locate front rails in the front-to-back direction as required by equipment

to be racked. Once located, be sure to leave an equal gap at the top and

bottom of each rail.

NOTE: While front rails are typically mounted fully forward in

the cabinet, this position may not provide adequate clearance

when accessory doors (purchased separately) are added.

Always consider the forward space for knobs, connections,

etc. as required by the installed components.

¼-20 He

x Bolt for

Rail Adjustment

c. If equipped with rear rack rails, use tape measure to locate rear rail

within respect to the front rail surface. This distance will vary with racked

gear requirements. Again, be sure to leave an equal gap at the top and

bottom of each rail.

NOTE: If the flush rear door (typical on most cabinets) is to be

used, verify rear door lock will not interfere with racked

equipment.

d. Once rails are located as required, use 3/8” hex socket driver to torque

into place. Recommended torque: 82 ± 2 in-lbs.

P/N 491548 Rev A

/4-20 Hex Bolt

Bekijk gratis de handleiding van Atlas Sound Texas Tough TT35-35V, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.