Ashly DigiMIX 24 handleiding
Handleiding
Je bekijkt pagina 8 van 36
Operating Manual - digiMIX24 Digital Mixer
8
2.12 FX 1 & 2 Level Controls, Send, and Mute Button
This mixer has built-in effects including reverbs, delay, chorus, anger, tremolo, plus combinations. Up to 104 effects can be
custom congured, saved, and loaded from mixer memory. Only two effects can be used at a time.
Press the FX1 or FX2 button beneath the touchscreen to dene or load the currently available effects (sec. 2.44). Then press the FX1
or FX2 Send button and use the touchscreen Parameter Adjust fader or the Adjust Parameter knob (sec. 2.27) to set the level of each
input that you want sent to each effect. Pre/Post effect send status is also assigned here. An alternate method of applying effect to
an input channel is to select an input, press the Assign button, then select and adjust the resulting touchscreen FX1 or FX2 controls.
Once FX1 and FX2 have been dened and desired input channel sends have been adjusted, each FX bus must be routed to the
main, aux, or subgroup outputs as desired. Press the FX1 or FX2 Select button, then press the Assign button, then select the main
or sub outputs using the touchscreen or with the buttons below the touchscreen. Similarly assign and adjust the FX level sent to
Aux outputs using the touchscreen parameter adjust control for each aux.
The master FX1 and FX2 knobs, when selected, work along with the motorized fader to control the FX level sent to the stereo
main and four subgroup outputs as assigned. FX level sent to the aux outputs is adjusted by using the touchscreen assign window
or the aux level controls, again while FX1 or FX2 is selected. Press the FX1 or FX2 mute button to silence the effect or compare
the sound with/without effect.
2.13 Main Volume Control
This control adjusts the stereo output level to the main L/R outputs. When the main select button is pressed (sec. 2.3), this control
works together with the motorized fader and touchscreen.
2.14 Ctrl Room Level Control
This adjusts the level of the control room outputs. Control room outputs always use
the post-fader signal from the main L/R outputs.
2.15 Headphones Level Control
This adjusts the headphone output level. The headphones default to L/R post-fader signal
unless an input, output, subgroup, FX, or DCA group is assigned to the solo bus. (sec 2.19)
2.16 DCA Set Button
Digital controlled ampliers (DCA1-6) are used to combine multiple inputs, aux or
sub outputs, or FX outputs into one mix group for simplied control of that group.
DCA groups allow the relative fader position of each member to be preserved while
adjusting their overall combined level as a group. It also allows the group to be instantly
muted. This is typically used for grouping vocals, drums, choir or orchestral sections,
etc. DCA groups must rst be dened before using EZ-Mode (sec 6.4).
To dene a DCA group, rst press the DCA Set button so that it ashes, then select
one of the six DCA button on the mixer or touchscreen, then select the individual
channels to combine for that DCA group. When nished, press the DCA Set button
again to store settings. Channels can be assigned across multiple DCA groups. To
clear the currently selected DCA group, press the DCA set button, then press DCA
clear on the touchscreen.
2.17 DCA1-6 Buttons
These six buttons are used to select a pre-dened DCA group for main fader, mute, or
solo control. If the DCA group is not dened, a touchscreen message appears requiring a response before proceeding.
2.18 Motorized Fader
This is the primary level control for all inputs, main output, aux and sub outputs, effects master, and DCA control. Press the select
button on any input or output, and the motorized fader will control its level. The fader works together with other level controls
used for the same selected signal. Motorized fader speed can be adjusted in the system screen (sec. 5.2).
Bekijk gratis de handleiding van Ashly DigiMIX 24, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Ashly |
| Model | DigiMIX 24 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 10179 MB |
