Zodiac Vortex-Pro VX40 handleiding

24 pagina's
PDF beschikbaar

Handleiding

Je bekijkt pagina 22 van 24
Problem Cause Solution
Theashingindicatorlights
(VX40)orerrorcode(VX50
4WDandVX554WD)
appearjustafterstart.
NOTE:Ifashinglightsare
accompaniedbyanerror
codeonthedisplay,referto
Control box Error Codes.
Floatingcablemaynotbeplugged
intothecontrolboxcorrectly.
Unplugoatingcablefromthecontrolboxand
reconnect.
Cleanermaynotbefullysubmerged. Removecleanerfromthepoolandre-submerge,see
Submerging the Cleaner.
Cleanermayneedtoberesetand
beginanewcycle.
TurncontrolboxpowerOFF,thenbackON,then
restartthecleaner.
Propellermaybejammedandnot
turningcorrectly.
ContactZodiacAfterSalesSupportat1300763021.
Wheelsmaybejammedandnotturn-
ingcorrectly.
ContactZodiacAfterSalesSupportat1300763021.
Theashinglightsappear
duringthecleaningcycle.
Cleanermaybesuckingair(lightswill
appearafter60secondsairintake)
Removecleanerfromthepoolandre-submerge,see
Submerging the Cleaner.
Thecleanerdoesnotstay
rmlyonthepoolbottom.
Thereisairintheappliancecasing. Submergethecleanerfollowingtheprocedurein
Submerging the Cleaner.
Theltercanisterisfullordirty. Cleantheltercanister,seeCleaning the Filter
Canister.
Thecleanerdoesnotorno
longerclimbsthepoolsides.
Theltercanisterisfullordirty. Cleantheltercanister,seeCleaning the Filter
Canister.
Sidesofpoolareslipperyorslimy.
Althoughthewaterseemsclear,
microscopicalgae,invisibletothe
humaneye,arepresentinthepool.
Asaresultthepoolsidesbecome
slipperyandpreventthecleanerfrom
climbing.Checktyresforwearand
replaceasnecessary.
Doashockchlorinationtreatment.DONOTleavethe
cleanerinthepoolduringthistreatment.
Onstartupthecleanerdoes
notmove.
Notsuppliedwithelectricity. Theoutlet,thecontrolboxisconnectedto,isnot
supplyingelectricalpower.Checkthattheoutlet
towhichthecontrolboxisconnectedisreceiving
electricity.
UnitisturnedON. Checkthatyouhavestartedone(1)ofthetwo(2)
programsandcheckthattheindicatorfortheselected
programislit.Iftheindicatorlightisnotlit,turnthe
wheelsthendisconnectthecontrolboxandwaitat
least20secondsbeforereconnecting.Iftheproblem
persists,contactZodiacAfterSalesSupportat1300
763 021.
Cableistanglinginthepool Toomuchcablelengthinthewater. Donotunraveltheentyrecablelength.
Placeonlytherequiredlengthofcableinthewater
andplacetherestonthesideofthepool.
FollowtheprocedureinCord Tangling toavoidand
correcttangledcord.
Thecleanerisnotcleaning
effectively.
Thebrusheshavebecomesmoothor
the"wear"indicatorshows.
Replacethebrushesfollowingtheprocedurein
Replacing the Brushes.
Filtercanisterisfullordirty. Cleantheltercanisterfollowingtheprocedurein
Cleaning the Filter Canister.
Floatingcableisexcessivelycoiledor
kinked.
Makesuretheoatingcableisspreadoutoverthe
pool.Ensurethecableisnottootightlywrappedor
coiledwhenstoring.Iftheproblempersists,laythe
cablestraightinthesuntorelaxitandremovekinks.
8.3 General Troubleshooting
The following table lists some of the common symptoms, causes, and solutions for correcting cleaner operation
problems.
H0516700_REV A
22

Bekijk gratis de handleiding van Zodiac Vortex-Pro VX40, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

MerkZodiac
ModelVortex-Pro VX40
CategorieNiet gecategoriseerd
TaalNederlands
Grootte4454 MB