Zodiac Ei3 handleiding
Handleiding
Je bekijkt pagina 15 van 20
Page 15
Page 14
Ei3 Saltwater Chlorinator | Installation Manual
<-PROGRAMMING
-LOW MODE
-SLAVE MODE
MAIN MENU
<-FILTER PUMP
-SWC
-AUX/LIGHTS
PROGRAMMING
<-PUMP TIMER 1
-PUMP TIMER 2
FILTRATION TIMER
<-PUMP 1 ON
-PUMP 1 OFF 12:30
04:30
FILTRATION TIMER
10. Whenaltrationprogramhasbeenconrmed
the letter “P” is displayed on the top right of
the screen.
23:04 ON P
Manual activation of the device (pressing )
takes priority over the timer. If no filter pump is
connected, the controller will only start chlorination.
If a filter pump has been connected the filter pump
will start along with chlorination. All programs will
still be valid and will resume normal operation the
next cycle.
7.3.4 Salt Water Chlorinator (SWC)
Programming
If a filtration program has been set, the chlorination
program will be identical to the filtration program(s)
by default. They can be changed, however the
chlorination program(s) cannot be activated outside
of the filtration Program(s) for safety reasons.
1. Press
.
2. Use to select “Programming”
then press
.
3. Use to select “SWC” then press .
4. Use to select “SWC Timer 1” or “SWC
Timer 2” then press
.
5. Use to select the hour for the SWC on
time then press
.
6. Use to select the minutes for the SWC
on time then press
.
7. Use toselectthehourfortheSWCo
time then press
.
8. Use to select the minutes for the SWC
otimethenpress
.
9. Press to exit.
<-PROGRAMMING
-LOW MODE
-SLAVE MODE
MAIN MENU
<
-RESET TIMERS
-SWC
-AUX/LIGHTS
PROGRAMMING
<
-SWC TIMER 2
-=FILTER PUMP
-SWC TIMER 1
SWC TIMER
<
SWC TIMER
-SWC1 ON
-SWC 1 OFF 12:30
04:30
The “T” symbol is displayed in the upper right hand
corner of the LCD display on the home screen if
the programming is valid.
The “P” symbol is displayed in the upper right-hand
corner of the LCD display on the home screen if a
valid filter pump and chlorinator program has been set.
23:04 ON T 23:04 ON P
7.3.5 AUX/Lights Programming
1. Press
.
2. Use to select “Programming”
then press
.
3. Use to select “AUX/Lights” then press .
4. Use to select “AUX 2 Timer” then press
.
5. Use to select the hour for the AUX on
time then press
.
6. Use to select the minutes for the AUX on
time then press
.
7. Use toselectthehourfortheAUXo
time then press
.
8. Use toselecttheminutesfortheAUXo
time then press
.
9. Press to exit.
<-AUX/LIGHTS
-PROGRAMMING
-LOW MODE
-SLAVE MODE
-REVERSING
-HELP MENU
-LANGUAGE
MAIN MENU
<
AUX/LIGHTS
-ASSIGN LIGHTS
-AUX 2
<
AUX 2
-OFF
-ON
-SET TIMERS
<
AUX TIMER
-AUX 2 ON
-AUX 2 OFF 12:30
04:30
7.4 Reversing
IMPORTANT
Adjusting your cell reversal times will result in voiding
of warranty. You must consult with Zodiac on 1300 763
021 or your local pool care professional before making
any adjustments.
The chlorinator uses a smart polarity reversal
system. Periodic polarity reversal will prevent
scaling of the cell plates. The time between each
reversal is factory set at 5 hours. This setting
is optimal for most water conditions. However,
Depending on the calcium hardness of the water,
you may need to adjust the reversal time. More
calcium in the water will require less time between
reversals. Water with less calcium can be given
more time between reversals. Shorter reversal
times will cause more wear of your cell plates. The
polarity reversal interval can be adjusted from 2 to
8 hours in 1-hour steps.
Bekijk gratis de handleiding van Zodiac Ei3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zodiac |
| Model | Ei3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2612 MB |
