Yato YT-8303 handleiding
Handleiding
Je bekijkt pagina 10 van 44
10
ORIGINAL INSTRUCTIONS
EN
get acquainted with the charging instructions provided by the manufacturer of the accumula-
tor and observe them.The accumulator and the rectifi er must be always placed on an even,
fl at and hard surface. Do not incline the accumulator.Before you connect the plug of the pow-
er cord of the rectifi er, make sure the power supply network parameters of the power supply
network correspond to the parameters indicated in the rating plate of the rectifi er.The rectifi er
must be placed as far from the accumulator as it is permitted by the cables with terminals.
Do not overstretch the cables. Do not place the rectifi er on the accumulator being charged
or directly above it. The fumes generated while charging the accumulator may cause corro-
sion of the internal components of the rectifi er, which may in turn cause its damage.Do not
smoke or approach accumulators with an open fl ame. Do not ever touch the terminals of the
rectifi er, when it is connected to the power supply network.Do not ever start the engine while
charging the accumulator.Before each use check the conditions of the rectifi er, including the
conditions of the power cord and the charging conductors. Should any damage be detected,
stop using the rectifi er. Damaged cables and conductors must be replaced with new ones in
a professional workshop.Before any maintenance of the rectifi er is executed, make sure the
plug of the power cord has been disconnected from power supply socket.The rectifi er must
be stored away from unauthorised persons, particularly children. Also during work make sure
the rectifi er is placed outside the reach of unauthorised persons, particularly children.Before
connecting the terminals of the rectifi er, make sure the terminals of the accumulator are clean
and free from corrosion. Provide the best possible electric contact between the terminal of
the accumulator and the terminal of the rectifi er.Do not ever charge a frozen accumulator.
Before you commence charging, move the accumulator to a place in which the electrolyte
may totally defrost. Do not heat accumulators in order to accelerate defrosting.Preclude any
leakage from accumulators. Any leakage from the accumulator on the rectifi er may cause a
short-circuit and thus an electric shock, which may be dangerous for health and life.
OPERATION OF THE RECTIFIER
Preparation of the accumulator for charging
Get acquainted with the charging instructions provided along with the accumulator and observe them. In the case of the so called
„wet” acid-lead accumulators” it is necessary to check the level of electrolyte and, if required, replenish it with distilled water to
the level indicated in the documentation of the accumulator. While replenishing the level of electrolyte, observe strictly the recom-
mendations indicated in the documentation of the accumulator.
Connect the terminals of the rectifi er to the terminals of the accumulator; make sure the terminal of the rectifi er marked with a „+”
is connected to the terminal of the accumulator marked with a „+” and the terminal of the rectifi er marked with a „-” is connected
to the terminal of the accumulator marked with a „-”.
Connect the plug of the power cord to the power supply socket.
Press the „ON/OFF” button and hold it approximately 0.5 sec.; it will turn the device on, which will be indicated on the display
by the „000” symbol. The rectifi er is in the standby mode. In order to turn the rectifi er off during any operating mode, press the
„ON/OFF” button and hold it for approximately 1 sec.
Function of the buttons
„BATTERY TYPE” (in YT-8303) – permits to select the kind of the accumulator being charged. The selection is confi rmed with a lit
diode: GEL” – means a lead-gel accumulator; „AGM” – means an AGM accumulator; „WET” – means an acid-lead accumulator. In
case of any doubts as to the kind of accumulator, contact the manufacturer or the seller, in order to establish the type.
„2/6/12 A SELECT” (in YT-8302); „2/6/10/15 A SELECT” (in YT-8303) – permits to select the charging current in amperes; the
selected value will be indicated in the display of the rectifi er. The rectifi er will commence charging after approximately 1 sec. from
the selection of the value.
Selecting the value of the charging current, consider the instructions provided by the manufacturer of the accumulator, but the
Bekijk gratis de handleiding van Yato YT-8303, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Yato |
| Model | YT-8303 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4687 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart |
| Ingebouwd display | Ja |
| Gewicht | 1625 g |
| Soort | Acculader voor de auto |
| Gebruikershandleiding | Ja |
