Yato YT-8271 handleiding

Niet gecategoriseerd

Yato

40 pagina's

PDF beschikbaar

Handleiding

ORIGINAL INSTRUCTIONS

PROPERTIES OF THE TOOL

The soldering tool has been designed for the purpose of soldering metals with tin and lead binders for soft soldering. A correct,

reliable and safe functioning of the tool depends upon appropriate operation, and therefore:

Before work with the tool, read the complete instruction and keep it.

The supplier will not be held responsible for any damage and injuries which occur as a result of inappropriate applications of the

tool, failure to observe safety regulations and the recommendations speciﬁ ed in these instructions. Improper application of the tool

will also cause cancellation of any guarantee rights due to incompliance with the sales contract.

EQUIPMENT

The soldering tool is provided complete and has no additional accessories.

TECHNICAL DATA

Parameter Unit of measurement Value

Catalogue number YT-8271 YT-8272 YT-8273

Power supply mains voltage [V~] 230 - 240

Power supply mains frequency [Hz] 50

Rated power [W] 30 60 80

Heating time [min] 3 2,5 2

Working temperature of the soldering tip [

C] 350 430 450

Maximum temperature of the soldering tip [

C] 400 500 520

Dimensions of the soldering tip [mm] Ø3,8 x 70 Ø6 x 78 Ø6,8 x 64

Durability of the soldering tip [h] > 60

Mass [kg] 0,07 0,09 0,11

Electric insulation class I

Protection rating IP20

SAFETY USE INSTRUCTIONS

The soldering tool may be connected solely to the 230V/50Hz mains. In order to avoid ﬁ re and burns, always use special non-ﬂ ammable

bases under the soldering tool. Once the soldering tool has been heated, it must be held solely by the handle. Touching of the soldering

tip or other metal elements of a hot soldering tool may cause burns. Do not permit any contact of the power supply cable with hot metal

elements since this might result in an electric shock. If the cable is damaged, the soldering tool must be disconnected from the power

supply mains. It is prohibited to work with a soldering tool with a damaged power supply cable. A damaged cable must by replaced by an

authorised service centre. Do not repair damaged electric cables of the tool. After work, the tool must be placed on the base to cool. This

is the only acceptable manner of cooling the tool. Do not cool the soldering tool placing it in water, since this may cause an electric shock.

The soldering tip of the soldering tool must be replaced solely when the power supply if oﬀ . The plug of the power supply cable must be

disconnected from the mains. Before you proceed to replace the soldering tip, make sure the soldering tool has cooled. The soldering tip

must be inserted until you feel resistance. Fasten the soldering tip in the ﬁ xture securely. Do not heat the soldering tool if a soldering tip is

not installed. A lack of a soldering tip during heating may cause a premature wear of the heating element of the soldering tool. Before you

proceed to heating, make sure the soldering tip is securely fastened to the soldering tool. Maintain the heating element and the soldering tip

of the soldering tool clean. It is prohibited to touch electric cables insulation with a hot soldering tip. It is prohibited to use the soldering tool

in high humidity conditions and in an explosive atmosphere containing gases and explosives or caustic dusts. Do not solder live element!

GENERAL SAFETY CONDITIONS

NOTE! Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, ﬁ re or injuries. The

notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and

wireless ones.

OBSERVE THE FOLLOWING INSTRUCTIONS

Place of work

The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of accidents. Do not

work with electric tools in explosive environments, or those which contain inﬂ ammable liquids, gases or vapours. Elec-

tric tools generate sparks, which may cause a ﬁ re in case of contact with inﬂ ammable gases or vapours. Do not allow children

and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.

Bekijk gratis de handleiding van Yato YT-8271, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.