Yaesu VR-5000 handleiding
Handleiding
Je bekijkt pagina 37 van 64
VR-5000 OPERATING MANUAL 35
3. To change to a different PMS frequency pair, press the numerical keys on the keypad
corresponding to the PMS register you wish to use. For example, if you are on PMS
register “00” and wish to use PMS register “03,” press
[
0
]
¯
[
3
]
while PMS scanning
is engaged. Scanning will begin on the new register without further action.
4. To reverse the direction of the scan (i.e. toward a lower frequency, instead of a higher
frequency), turn the DIAL knob one click in the counter-clock direction or press the
[
T
(
W
)]
key momentarily while the VR-5000 is scanning. To revert to scanning toward
a higher frequency once more, rotate the DIAL knob one click clockwise or press the
[
S
(
X
)]
key momentarily.
5. Press the
[
V/M
(
MW
)]
key to disable the PMS scanner, and return to VFO mode.
Adjusting the PMS Scanner (Including PMS Register Change)
1. Press the
[
F
]
key momentarily, then press the
[
PMS
(
PMS SET
)]
key.
2. To change the PMS register on which you wish to scan, first confirm that the cursor is
pointing to “
PMS CHPMS CH
PMS CHPMS CH
PMS CH,” then press the
[
ENT
(
SET
)]
key.
3. Rotate the DIAL knob to select the new PMS register; now press the
[
ENT
(
SET
)]
key.
4. If you only wish to change the PMS register, skip to step 7.
5. Rotate the DIAL knob to set the cursor to the “
MISCMISC
MISCMISC
MISC” menu option, then press the
[
ENT
(
SET
)]
key.
6. Rotate the DIAL knob to set the cursor to the desired menu from the following list;
remember that these settings will only be applied during PMS operation.
ScanStopScanStop
ScanStopScanStop
ScanStop: Selects the Scan Resume mode among “
HOLDHOLD
HOLDHOLD
HOLD,” “
DELAYDELAY
DELAYDELAY
DELAY,” and “
PAUSEPAUSE
PAUSEPAUSE
PAUSE,”
as described previously. Press the
[
•
(
BEEP
)]
key to change selections.
(1) In the “
HOLDHOLD
HOLDHOLD
HOLD” mode, when a signal is received the scanner will hold for
2 second, then the scanner will stop.
(2) In the “
DELAYDELAY
DELAYDELAY
DELAY” mode, when a signal is received the scanner will hold
until the signal disappears,
then the scanner will resume after 2 seconds.
(3) In the “
PAUSEPAUSE
PAUSEPAUSE
PAUSE” mode, when a signal is received the scanner will hold
for 2 second, then scanner will resume after 2 seconds.
S-LvlScanS-LvlScan
S-LvlScanS-LvlScan
S-LvlScan: The scanner will halt and pause on the frequency when there is a signal
strong enough to stops on.
VCSVCS
VCSVCS
VCS: Enables/disables the VCS (Voice Channel Scan) feature via pressing the
[
•
(
BEEP
)]
key. When enable the VCS feature is enabled, the scanner will
only halt and pause on the frequency that is having the voice signal.
ATTATT
ATTATT
ATT: Enable/disable the RF signal Attenuator via pressing the
[
•
(
BEEP
)]
key.
DSPDSP
DSPDSP
DSP: Turns the Digital Signal Processing system On or Off.
7. When you have made your selection(s), rotate the DIAL knob to select the “
ENDEND
ENDEND
END”
menu option, then press the
[
ENT
(
SET
)]
key.
8. Confirm that the cursor is now pointing to the “
WRITEWRITE
WRITEWRITE
WRITE” menu option, and press the
[
ENT
(
SET
)]
key.
Scanning
Bekijk gratis de handleiding van Yaesu VR-5000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Yaesu |
| Model | VR-5000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8268 MB |
