Yaesu VR-5000 handleiding

64 pagina's
PDF beschikbaar

Handleiding

Je bekijkt pagina 34 van 64
VR-5000 OPERATING MANUAL32
Scanning
Here is the procedure for setting up the Scan-Resume mode for VFO scan-
ning:
1. Press the
[
F
]
key momentarily, then press the
[
ENT
(
SET
)]
key.
2. Confirm that the cursor is on the “
VFOVFO
VFOVFO
VFO” menu option, then press the
[
ENT
(
SET
)]
key.
3. If you are setting the Scan-Resume mode for the MAIN VFO, rotate the dial to put the
cursor on the “
MainScanMainScan
MainScanMainScan
MainScan” menu option.
4. Press the
[
(
BEEP
)]
key to select the desired Scan-Resume mode: “
DELAYDELAY
DELAYDELAY
DELAY,” “
PAUSEPAUSE
PAUSEPAUSE
PAUSE,”
or “
HOLDHOLD
HOLDHOLD
HOLD.”
5. Rotate the DIAL knob to set the cursor to the “
ENDEND
ENDEND
END” menu option, then press the
[
ENT
(
SET
)]
key.
6. Confirm that the cursor is on the “
WRITEWRITE
WRITEWRITE
WRITE” menu option, then press the
[
ENT
(
SET
)]
key to save a new setting and exit.
Here is the procedure for setting up the Scan-Resume mode for PMS scanning:
1. Press the
[
PMS
(
PMS SET
)]
key to enter the “PMS” mode (described below).
2. Press the
[
SCAN
(
M-S SCAN
)]
key to halt PMS scanning, if engaged.
3. Press the
[
F
]
key momentarily, then press the
[
PMS
(
PMS SET
)]
key.
4. Rotate the DIAL knob to select the “
MISCMISC
MISCMISC
MISC” menu option, then press
[
ENT
(
SET
)]
.
5. Rotate the DIAL knob to select the “
ScanStopScanStop
ScanStopScanStop
ScanStop” menu option.
6. Press the
[
(
BEEP
)]
key, repeatedly if necessary, to select “
DELAYDELAY
DELAYDELAY
DELAY,” “
PAUSEPAUSE
PAUSEPAUSE
PAUSE,” or
HOLDHOLD
HOLDHOLD
HOLD,” as desired.
7. Rotate the DIAL knob to select “
ENDEND
ENDEND
END,” then press
[
ENT
(
SET
)]
.
8. The display should now indicate “
WRITEWRITE
WRITEWRITE
WRITE;” press the
[
ENT
(
SET
)]
key again to save
the new setting and exit to normal operation.
MEMORY SCANNING
1. Press the
[
V/M
(
MW
)]
key, if needed, to enter the “MR” (Memory Recall) mode.
2. Press the
[
T
(
W
)
/S
(
X
)]
keys to select the memory bank on which you wish to do
memory channel scanning.
3. Press the
[
SCAN
(
M-S SCAN
)]
key to initiate memory channel scanning in an upward
direction (in the current memory bank).
4. If the scanner encounters a signal strong enough to open the squelch, the scanner will
halt and pause on that channel. Scanning will resume according to the protocol you
selected in the previous discussion.
5. To reverse the direction of the scan (i.e. toward a lower memory channel, instead of a
higher memory channel), turn the DIAL knob one click in the counter-clock direction
(or press the
[
T
(
W
)]
key momentarily) while the VR-5000 is scanning. To revert to
scanning toward a higher memory channel once more, rotate the DIAL knob one click
clockwise (or press the
[
S
(
X
)]
key momentarily).
6. Press the
[
SCAN
(
M-S SCAN
)]
key to disable memory channel scanning.

Bekijk gratis de handleiding van Yaesu VR-5000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

MerkYaesu
ModelVR-5000
CategorieNiet gecategoriseerd
TaalNederlands
Grootte8268 MB