Yaesu VR-5000 handleiding
Handleiding
Je bekijkt pagina 33 van 64
VR-5000 OPERATING MANUAL 31
Scanning
VOICE Scanning
1. Press the
[
F
]
key momentarily, then press the
[
V/M
(
MW
)]
key.
2. Rotate the DIAL knob to set the cursor to the “
ChannelChannel
ChannelChannel
Channel” menu option, then press the
[
ENT
(
SET
)]
key.
3. Using the
[
T
(
W
)
/S
(
X
)]
keys or the keypad, select the memory bank on which you
wish to perform VOICE scanning, then press the
[
BANK
]
key.
4. Rotate the DIAL knob to set the cursor to the
“
VCSVCS
VCSVCS
VCS” menu option, then press the
[
•
(
BEEP
)]
key to enable VOICE scanning.
5. Rotate the DIAL knob to set the cursor to the
“
ENDEND
ENDEND
END” menu option, then press the
[
ENT
(
SET
)]
key.
6. Confirm that the cursor is on the “
WRITEWRITE
WRITEWRITE
WRITE”
menu option, then press the
[
ENT
(
SET
)]
key to save the new setting and exit to normal
operation.
Setting the Scan-Resume Technique
Three options for the Scan-Resume technique are available. These options may be set
independently for Memory Scan, VFO Scan, and PMS (Band-Segment) Scan operation.
DELAYDELAY
DELAYDELAY
DELAY: In this mode, the scanner will halt on a signal it encounters, and will hold until the
signal disappears. After the squelch closes when the received station quits trans-
mitting, scanning resumes automatically. The scanning-restart delay time (default
interval: 2 seconds) is set by the “
M-P.DELAYM-P.DELAY
M-P.DELAYM-P.DELAY
M-P.DELAY” menu selection.
PAUSEPAUSE
PAUSEPAUSE
PAUSE: In this mode, the scanner will halt on a signal it encounters. After a programmed
time interval (set by the “
M-PAUSEM-PAUSE
M-PAUSEM-PAUSE
M-PAUSE” menu selection), the scanner will resume,
whether or not the signal has disappeared.
HOLDHOLD
HOLDHOLD
HOLD: In this mode, the scanner will halt on a signal it encounters. It will not restart
automatically; you must manually re-initiate scanning if you wish to resume.
However, the “
M-HOLDM-HOLD
M-HOLDM-HOLD
M-HOLD” menu selection provides a “restart” window within which,
if the incoming signal disappears, the scanner will resume; this allows scanning to
proceed if the squelch is opened by a brief incoming signal burst.
Here is the procedure for setting up the Scan-Resume mode for Memory scanning:
1. Press the
[
V/M
(
MW
)]
key, if necessary, to enter the “MR” (Memory Recall) mode.
2. Use the
[
T
(
W
)
/S
(
X
)]
keys to select the desired memory bank.
3. Press the
[
BANK
]
key, then rotate the dial to select the “
ScanStopScanStop
ScanStopScanStop
ScanStop” menu option.
4. Press the
[
•
(
BEEP
)]
key, repeatedly if necessary, to select “
DELAYDELAY
DELAYDELAY
DELAY,” “
PAUSEPAUSE
PAUSEPAUSE
PAUSE,” or
“
HOLDHOLD
HOLDHOLD
HOLD,” as desired.
5. Rotate the DIAL knob to select “
ENDEND
ENDEND
END,” then press the
[
ENT
(
SET
)] key
.
6. The display should now indicate “
WRITEWRITE
WRITEWRITE
WRITE;” press the
[
ENT
(
SET
)]
key again to save
the new setting and exit to normal operation .
Bekijk gratis de handleiding van Yaesu VR-5000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Yaesu |
| Model | VR-5000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8268 MB |
