Xblitz X7 handleiding
Handleiding
Je bekijkt pagina 9 van 56
16 17
Check: PARKING MODE/MONITOR and MOVEMENT DETECTION - funcon
designed to operate while the vehicle is parked. Deacvate the funcon, before
seng o, as it may cause the camera to switch on and o and make random
fragments of route recordings.
If the funcons are disabled, check if the fault occurs without the memory
card inserted.
5. The camera records fragments of the route / randomly ongoing recordings
Check: MOVEMENT DETECTION - a funcon designed to operate while the
vehicle is parked.
You need to deacvate the funcon, before seng o, as it can cause the
camera to switch on and o and make random fragments of route recordings.
If the funcon is deacvated, check if the fault occurs without a memory card
inserted.
6. The device shows the message „card full” or does not read the card
Check the „G-sensor” and „parking mode” funcons and set them to minimum.
The card must be formaed in the computer in the FAT32 or exfat le system
(depending on the card) and then in the recorder.
Also check: Is the selected card capacity and specicaon (micro SD, class 10 -
U1, V10 addionally recommended) suitable for your device (we recommend
using cards from reputable manufacturers, we recommend: Kingston, Samsung,
Sandisk).
If you encounter an error at any stage, replace the card with a new one from an
ocial distribuon.
7. The device records noise, distorted, unclear sound
The device has a highly sensive microphone that records any ambient noises.
The recorded sounds may overlap. Windscreen air vents can also distort the
sound.
8. The device does not respond
Press the Reset buon briey or return the device to factory sengs.
9. Transverse stripes are present in the footage
Incorrect seng of the frame rate value. Set the frequency value to „50Hz” or
„60Hz” depending on local sengs.
10. Handle detaches from windshield/does not sck
Degrease the surfaces well before mounng the holder on the glass. Remember
to avoid high temperatures, which can cause deformaon of the holder, and
damage to the recorder itself.
NOTES:
- G-SENSOR - a funcon thanks to which recordings with recorded overloads (e.g.
uneven road surface, braking, driving o a kerb or over a speed bump, etc.) are
protected from being overwrien. If the user uses this funcon, the memory card
must be formaed periodically on the computer and then on the camera. Ul-
mately, each le on the data carrier will be protected from being overwrien and
the device will not be able to record a further route - it will not record in a loop.
We suggest seng the sensor according to your driving style and road condions.
This opon can also be completely disabled, in which case each oldest le will be
overwrien and the card will not need to be formaed periodically.
- PARKING MODE/MONITOR - a funcon designed to operate while the vehicle is
parked, uses baery power* if the recorder is fully charged - (*if it has a built-in
baery) . In this case, the camera starts recording a video of a few seconds aer
detecng a shock - unl the baery is discharged. When using this funcon, bear in
mind the baery of the device, which needs to be recharged aer the funcon ac-
vates (starts). You should deacvate the funcon, before seng o on a journey,
as it may cause the camera to switch on and o and make random fragments of
recordings from the route.
*The constant power supply in the vehicle may cause this funcon to behave
dierently, e.g. leaving the camera on, which may drain the car baery.
- MOVEMENT DETECTION - a funcon designed to operate while the vehicle is par-
ked - requires constant power and the camera must remain switched on. The DVR
will start recording automacally when moon is detected, and will stop recording
a few seconds aer there is no movement in front of the camera lens. Please note
that this funcon may drain the car baery.
You need to deacvate the funcon, before seng o, as it can cause the camera to
switch on and o and make random fragments of route footage.
Due to connuous product improvement, the manufacturer reserves the right
to make changes to the device and its kit without prior noce. Some funcons
described in this manual may dier slightly in reality.
09. NOTE
1. Due to connuous product improvement, the manufacturer reserves the
right to make changes to the device and its kit without prior noce. Some
funcons described in this manual may dier slightly from reality.
2. Use only the original charger with a charging current of 5V/1.5A. (Do not
plug directly into a 220/230V socket). Failure to follow the recommendaons
may damage the camera or lead to dangerous situaons.
3. The ‚Park Mode’ funcon only works on direct baery power or baery
power. It relies on the fact that when an impact is detected (depending on
the sensivity of the sensor set), the camera starts up and records for a
period of me according to the recording loop sengs or unl the baery is
discharged and then switches o, this allows the unit to remain in standby
mode for as long as possible. Parking mode recordings may be of lower qu-
ality due to the lower frame rate characterisc of this mode. The manufactu-
rer accepts no responsibility for failure to record any damage caused when
Bekijk gratis de handleiding van Xblitz X7, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Xblitz |
| Model | X7 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 7116 MB |
