Handleiding
Je bekijkt pagina 20 van 25
20
VAD DU SKA GÖRA OM DET UPPSTÅR ETT PROBLEM
Spishällen eller kokzonen kan inte slås på:
• Fel på anslutningen till elnätet.
• Skyddssäkringen har kopplats ur.
• Låsfunktionen har aktiverats.
• De tryckkänsliga knapparna är täckta av fett eller vatten.
• Ett föremål har placerats på en knapp.
Kontrollpanelen visar [ ]:
• Det finns inget kokkärl på kokzonen.
• Kokkärlet är inte kompatibelt med induktion.
• Diametern på kokkärlets botten är för liten.
Kontrollpanelen visar [ ]:
• Det elektroniska systemet är defekt.
• Koppla från och återanslut hällen vid strömbrytaren.
En eller alla kokzoner stängs av:
• Säkerhetssystemet har aktiverats.
• Du har glömt att stänga av kokzonen under en lång tid.
• En eller flera tryckkänsliga knappar är övertäckta.
• Kokkärlet är tomt och dess botten överhettad.
• Spishällen har också en automatisk minskning av värmesteget för att förhindra överhettning.
Kontinuerlig ventilation efter avstängning av spishällen:
• Detta är inte ett fel. Fläkten fortsätter att vara igång för att skydda de elektroniska kompo-
nenterna.
• Fläktkylningen stängs automatiskt av.
Det automatiska tillagningssystemet startar inte:
• Kokzonen är fortfarande varm [ H ].
• Det högsta värmesteget är inställt [ 9 ].
Kontrollpanelen visar [ ]:
• Se kapitlet ”Barnlåsfunktion”.
Kontrollpanelen visar [ ] eller [ ] eller [ ] :
• Se kapitlet ”Varmhållning”.
Kontrollpanelen visar [ ]:
• Se kapitlet ”Paus”.
Kontrollpanelen visar [ ] eller [ ] :
• Manöverknapparna är täckta av ett föremål eller vatten. Symbolen försvinner så snart knap-
pen släpps eller rengörs.
Kontrollpanelen visar [ ] :
• Spishällen är överhettad. Låt den svalna och slå sedan på den igen.
Kontrollpanelen visar [ ] :
• Fläktens luftintag är blockerat. Avlägsna blockeringen.
Kontrollpanelen visar [ ] :
• Spishällen är inte ansluten till elnätet. Kontrollera anslutningen och återanslut spishällen.
Kontrollpanelen visar [ ( ) ] :
• Stäng av kokzonen, ta bort alla kokkärl och låt hällen svalna. Starta om spishällen.
Kontrollpanelen visar [ ( ) ] :
• Stäng av kokzonen, ta bort alla kokkärl och låt spishällen svalna. Starta om spishällen.
Om någon av symbolerna ovan fortsätter att visas ska du ringa eftermarknadsservicen.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
Bekijk gratis de handleiding van Witt WIF70EVW, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Witt |
| Model | WIF70EVW |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 2623 MB |
