Handleiding
Je bekijkt pagina 28 van 59
28
PROGRAMMERING AF TILBEREDNINGSTID
Denne funktion bruges til at programmere tilberedningstiden, hvorefter ovnen automatisk slukker.
• Vælg den ønskede tilberedningsfunktion og temperatur ved hjælp af kontrolknapperne.
• Tryk på tasten for at tilgå programmeringsmenuen, og tryk igen, så ordet ”Dur” vises.
• Brug
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
tasterne til at indstille tilberedningstiden. Ordet ”Auto” blinker under
programmeringsfasen. Efter 7 sekunder starter madlavningsprogrammet, og symbolet
vises, mens ordet ”Auto” stopper med at blinke.
Når den indstillede madlavningstid er nået, lyder en alarm i 7 minutter, og symbolet ”AUTO”
blinker, mens symbolet slukker, og ovnen slukkes automatisk.
• Tryk på en hvilken som helst knap for at stoppe alarmen eller tryk på tasten for at slette
programmet.
PROGRAMMERING AF TILBEREDNINGSTID OG SLUKNING
Denne funktion bruges til at programmere ovnen til at tænde på et bestemt tidspunkt og slukke
automatisk efter madlavning.
• Indstil den ønskede madlavningsfunktion og temperatur ved hjælp af kontrolknapperne.
• Tryk på tasten for at gå til programmeringsmenuen, og tryk igen, så ordet ”Dur” vises.
• Brug
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
tasterne til at indstille tilberedningstiden.
• Tryk på tasten for at vise ”end”, og brug tasterne til at indstille det ønskede tidspunkt
for afslutning af tilberedningstiden.
Ordet ”Auto” blinker under programmeringsfasen. Efter 7 sekunder forlader programmet
menuen, og ordet ”Auto” stopper med at blinke. Når starttidspunktet for tilberedningen er nået,
vises symbolet og ovnen tænder automatisk.
Når den indstillede madlavningstid er udløbet, lyder en alarm i 7 minutter, og symbolet ”AUTO”
blinker, mens symbolet slukker, og ovnen slukkes automatisk.
• Tryk på en hvilken som helst knap for at stoppe alarmen, eller tryk på tasten for at slette
programmet.
LYDALARM
Ved afslutningen af hver forudindstillet funktion lyder en alarm, som slukker automatisk efter 7
minutter. Tryk på tasten for at slukke alarmen straks.
Der er tre forskellige typer lydalarmer tilgængelige på apparatet. For at vælge mellem dem, skal
du trykke på tasterne samtidig og derefter trykke på tasten, indtil ”Tone” vises. Vælg
derefter den ønskede ydalarm ved at trykke på knappen.
Brugsanvisning
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Bekijk gratis de handleiding van Witt Embrace 90, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Witt |
| Model | Embrace 90 |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 8313 MB |
