Wiesenfield WIE-PM-2500 handleiding
Handleiding
Je bekijkt pagina 9 van 37
16
NOTE !: The screws should be identically tightened. If
they are tightened too much, one of the rollers may stop
turning and / or the roller may become deformed. Also,
do not increase the pressure of the rollers by tightening
the screws in the event that the die is clogged.
LUBRICATING THE ROLLERS AND THE DIE
IMPORTANT: The rollers and the die should be lubricated
with bearing grease each time after 8 hours of machine
operation.
Press in the grease with the grease gun supplied with
the kit. Insert the end of the grease gun into the grease
injection hole as shown in the gure below.
To lubricate the roller bearings, they must rst be
dismantled from the device. For this purpose:
• Unscrew and remove the hopper and the top casing.
• Remove the rollers.
• Lubricate them with a grease gun.
OIL CHANGE
Change the oil after the rst 60 hours of operation.
To do this, you need to:
• Drain the old oil from the reservoir. Place a waste
oil container under the machine and undo the screw
marked „b“ in the gure below. Wait for the oil to
drain out. Tighten the screw „b“.
NOTE: Used oil must be disposed of in accordance
with local regulations.
• To pour fresh oil into the box, unscrew the oil ller
cap marked „a“ in the gure below. Pour in the oil
and close the ller cap.
WIE-PM-3000
a
b
a
b
WIE-PM-2500
EN
2
3
1
• After the clamping nut is removed , the holes for
attaching the bracket can be seen. To remove the
die, rst attach the bracket using the screws marked
as 1 and 2 in the picture. Then slowly screw in the
screw No. 3, the die will start to rise slightly.
• Remove the die. Clean it or replace it with a new one,
as the need may be.
• When re-installing the die into place and re-
assembling the device, proceed in the reverse order
as during disassembly.
ADJUSTMENT OF THE ROLLERS
The distance between the rollers and the die should be in
the range of 0.1-0.3 mm. The die should be able to rotate
freely under the rollers.
The adjustment is made with the screws marked in the
drawing below.
SPARE PARTS
• 10280152, 10280158 - Binder 2,5 mm
• 10280153, 10280159 - Binder 3 mm
• 10280154, 10280160 - Binder 4 mm
• 10280155, 10280161 - Binder 6 mm
• 10280156, 10280162 - Binder 8 mm
• 10280156, 10280163 - Press-Roller
• 10530000 - glue for pellets
SOLUTIONS PROBLEMS
Problem Possible
cause
Action
Die / rollers
get stuck or
clogged.
Wrong pellet
mixture or a
wrong die for
the mixture
Stop the machine
and clean the die
/ rollers and, if ne-
cessary, modify the
mixture as descri-
bed in this manual
(see 10530000) or
reduce the amount
of mixture poured
in at once or select
the appropriate die.
Pellets are not
produced.
There is a
burning smell,
there is smoke
coming from
the device or it
becomes very
hot.
Clogged die. Clean the die and
rollers. Modify
the pellet mixture
and use starch as
a binding material
and / or reduce the
amount of material
poured in at once.
Insucient
amount of pel-
lets produced.
Wrong
composition
of the pellet
mixture.
Modify the mixture
and make sure that
starch is used as a
binder.
Bent or
cracked shaft
(lever)
The bolts
holding the
shaft (lever)
are tightened
too much.
Replace the dama-
ged shaft (lever)
with a new one.
Worn die
and/or rolls
If a given side of the
die has a distance
from the rollers less
than 4 mm, it must
be replaced. The
service life of the
die is approx. 300
operating hours -
after this time, it
must be replaced.
Roller jamming
or jamming,
noise during
roller opera-
tion.
Damaged
bearing or
bearings
on rollers
(insucient
bearing
maintenance).
Replace the bearin-
gs with new ones.
Lubricate them
with bearing grease
before installation.
05.05.2022
EN
17
Bekijk gratis de handleiding van Wiesenfield WIE-PM-2500, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Wiesenfield |
| Model | WIE-PM-2500 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 27568 MB |
