Handleiding
Je bekijkt pagina 7 van 72
7
WipeClean™™ Cooktop Coating
Cleaning Routine (On Some Models)
IMPORTANT: Clean the cooktop according to these instructions
after each use to avoid soil build ups and to prolong the life of
your WipeClean™ Cooktop.
Everyday Cleaning:
1. Allow the cooktop to cool down completely before proceeding.
2. Spray the cooktop with water and soak for a minimum of
5 minutes, paying attention to cover the entire soiled area. For
heavy stains, soak for 20-25 minutes.
3. Using a paper or kitchen towel remove the initial layer of soil
from the surface.
4. Use a moist non-abrasive soft sponge and scrub the residual
soil from the surface.
5. With a paper or kitchen towel wipe off and dry the surface.
6. Repeat steps 2 through 5 as necessary for stubborn soils.
Extremely Tough Soils:
1. For extremely heavy soils, increase the amount of time
soaking in water up to 45 minutes.
2. If an extremely tough soil persists, apply a few dime-sized
drops of a non abrasive cooktop cleaner such as the affresh
®
Cooktop Cleaner to the affected areas to remove the
remaining soil from the surface. Gently apply the cleaner with
a paper towel.
� Wipe away the cleaner with a warm damp cloth after using
any detergent.
� Use of a scraper is not recommended as it might cause
potential cooktop scratches.
3. Important: Do not apply excessive pressure while using
detergents and do not use coarse or abrasive sponges with
them. Detergents containing aggressive particles may
damage your cooktop.
Tips & Tricks
� Detergents may contain abrasive particles or harsh chemicals:
pay attention to detergent’s type when cleaning and do not let
them sit on the surface for more than 10 minutes. Avoid these
items when it comes to cleaning your glass top stove:
• Steel wool and other scrubby, abrasive or course sponges
• Abrasive powder cleansers or abrasive detergents
• Chlorine bleach
• Rust remover
• Ammonia
• Glass window cleaners
� Light discoloration on the surface may happen if not cleaning
frequently and cooking for a long time or cooking over a soiled
surface: they usually do not compromise cleanability and
surface properties.
� Soaking with water will give the best results on cleaning:
longer soaking times will increase cleanability efficiency and
result, preserving cooktop surface over time.
� Do not slide pots on the surface or use it as a cutting board.
Small scratches on the surface may appear over normal use,
as in standard glass, without compromising its performance.
� Avoid soiling build up on the surface as it can damage your
product surface. Clean the cooktop surface after every spill,
this will help preserve the cooktop surface over time.
INSTALLATION INSTRUCTIONS
REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
� Tape measure
� Flat-blade screwdriver
� Phillips screwdriver
� Level
� Hammer
� Hand or electric drill
� Wrench or pliers
� Marker or pencil
� Flashlight
� Torque Wrench
� Masking tape
� 1/4" (6.4 mm) drive ratchet
� 1/4" (6.4 mm) nut driver
� 3/8" (9.5 mm) and 5/16"
(8 mm) nut driver
� 1/8" (3.2 mm) drill bit (for
wood floors)
� Tin snips or large wire
cutters (for cutting
ground-link strap if
necessary)
Parts supplied
Check that all parts are included.
� 10-32 hex nuts (attached to terminal block) (3)
� Direct wire lugs (3)
� #10 x 1
5
⁄
8
" (4.1 cm) screws (for mounting anti-tip bracket) (2)
� Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts needed
If using a power supply cord kit:
� A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 V minimum, 40 A or 50 A that
is marked for use with nominal 1
3
⁄
8
" (3.5 cm) diameter
connection opening and must end in ring terminals or
open-end spade terminals with upturned ends.
� A UL listed strain relief.
Check local codes. Check existing electrical supply. See the
appropriate “Electrical Requirements” section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
NOTE: Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
� It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on the
top right-hand side of the oven frame.
� To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood or
microwave hood combination that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
� The range should be located for convenient use in the kitchen.
� Recessed installations must provide complete enclosure of the
sides and rear of the range.
Bekijk gratis de handleiding van Whirlpool WSES7530RV, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WSES7530RV |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 11324 MB |
