Handleiding
Je bekijkt pagina 11 van 98
9. SMART CLEAN FUNCTION
Press and select “Smart Clean” Function.
Smart Clean
Press to activate the function: the display will
prompt you to carry out all actions needed to obtain
the best cleaning results: follow the indications and
then press
when done. Once all the steps have
been completed, when required, press
to activate
the cleaning cycle.
Please note: It is recommended to do not open the oven
door during the cleaning cycle to avoid a loss of water vapor
that could get an adverse eect on the nal cleaning result.
An appropriate message will start flashing on the
display once the cycle has finished. Leave the oven to
cool and then wipe and dry the interior surfaces with
a cloth or sponge.
10. DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display. The average duration
of the full function is around 100 minutes. Descale
can be initiated anytime by the entering the
then
selecting the "CLEANING FUNCTIONS" menu and the
Descale function.
The display will show you when it is time to run a
Descale cycle.
The number of hours of steam cycles that must pass
before the Decale messages are shown depends on
the water hardness level set on the appliance and on
the selected steam functions, proportionally with the
amount of steam generated.
The descaling procedure can also be performed
whenever the user desires a deeper cleaning of the
internal steam circuit.
Before to run the descaling phase, the appliance
will check if some residual water is contained into
the boiler, and a Drain cycle could be performed,
if needed. In this case, you will have to empty the
drawer after the Drain cycle, before continuing with
the Descale Phase.
Please note: to ensure that the water is cold, it is not
possible to perform this activity before 40 minutes have
elapsed from the last cycle (or the last time the product
was powered). During this waiting time, the display will
show the following feedback “WATER IS HOT”.
» PHASE 1/2: DESCALING (70 MIN)
When display will show <ADD 0.25 L OF SOLUTION>,
please pour the descaling solution in the drawer. For
best results in descaling, we recommend filling the
tank with a solution composed of 75 g of the specific
WPRO product and 250 ml of drinking water. WPRO
descaler is the suggested professional product for the
maintenance of the best performance of your steam
function in the oven.
Whirlpool will not be held responsible for any
damage caused by the use of other cleaning products
available on the market.
Once the descaling solution is poured inside the
drawer, press
to start the main descaling process.
The descaling phases do not need you to stay in front
of the appliance. After each phase is completed, an
acoustical feedback will be played and the display will
show instructions to proceed with the next phase.
Once the descaling phase has been completed, the
boiler will be drained: the descaling solution used
1+
= 75 g
+2
250 ml
3
during this phase will be poured into the extractable
drawer.
At the end of the drain, drawers has to be extracted
and emptied.
» PHASE 2/2: RINSING (30 MIN.)
To remove descale residuals from the drawer and
the steam circuit, rinse cycle has to be done. When
display shows <ADD 0.25 L OF WATER> fill the tank
with 0,25 L of drinking water, then press
to start
the rinsing. Do not turn off the oven until all the steps
required by the function have been completed.
Please note: if needed from the system, it could be
requested to emty the drawer and to repeat this
operation.
When Descale procedure is completed, it is suggested
to dry the cavity from potential water residuals. It will
be then possible to use all the steam functions.
Please note: during the Descale cycle, some noise could
potentially be heard since the oven pumps are activated
in order to guarantee the optimal descale efficiency.
Once the maintenance cycle has started, do not remove
the drawer unless requested by the appliance.
Please note: After the boiler gets filled by the descaling
solution and the display shows “DESCALING PHASE 1/2”,
the cycle should not be interrupted and/or the door
opened, otherwise the entire descaling cycle must be
repeated before being able to run any steam function.
11. MINUTEMINDER
It is possible to start a minute minder at any moment..
To activate this function, press
3s: The icon will
flash on the display.
MINUTE-MINDER
Press or to set the length of time you require and
then press
to activate the timer.
An audible signal will sound and the display will
indicate once the minuteminder has finished counting
down the selected time.
It is possible to activate a minute-minder also while a
cooking function is running.
While a cooking function is running, the timer will
continue to count down independently without
interfering with the function itself.
Bekijk gratis de handleiding van Whirlpool WCT7A9PHTSB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WCT7A9PHTSB |
| Categorie | Magnetron |
| Taal | Nederlands |
| Grootte | 16746 MB |
