Whirlpool W8F HS61BS handleiding
Handleiding
Je bekijkt pagina 7 van 137
EN
Daily Reference Guide
7
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The salt
indicator is lit
Salt reservoir is almost empty.
Rell the reservoir with salt (for more information - see FILLING THE SALT RESERVOIR).
Check the water hardness setting if necessary (see WATER HARDNESS TABLE).
The salt
indicator is
blinking
Salt reservoir is empty.
Rell the reservoir with salt as soon as possible. Using the appliance without salt may
cause damage to its internal components.
The rinse aid
indicator is lit
or blinking
Rinse aid dispenser is empty. (After rell the
rinse aid indicator may remain lit for a short
time).
Rell the dispenser with rinse aid (for more information - see FILLING THE RINSE AID
DISPENSER).
Descale
indicator is lit
or blinking;"dES"
alarm is displayed.
Limescale is accumulating on internal com-
ponents of the appliance.
Descale the appliance immediately using the Self Clean program and a commercially
available descaling product (see OPTIONS AND FUNCTIONS). Rell the reservoir with
salt. Check the water hardness setting. If the appliance is not descaled, it will stop
functioning.
The dishwasher
won’t start or
does not respond
to commands.
The appliance has not been plugged in
properly.
Insert the plug into the socket.
Power outage.
For safety reasons, the dishwasher will not restart automatically when power returns.
Close the door and press START/Pause button.
The dishwasher door is not closed.
NaturalDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
A cycle is interrupted by door opening for
more than 4 seconds.
Close the door within 4 sec. and press START/Pause button.
The control panel does not respond or F6
E1 is displayed.
Switch o the appliance by pressing the ON-OFF/Reset button, switch it back on
after approximately one minute and restart the program. If the problem persists,
unplug the appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows:
F7 E3 or F9 E1
The lter is clogged with food residues or
limescale
Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and
DESCALE INSTRUCTION).
The drain hose is kinked. Check the drain hose (see INSTALLATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The dishwasher
makes excessive
noise.
Dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in the
dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program, close
the door and press START/Pause.
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The lter is clogged with food residues or
limescale.
Clean the lter assembly (see CARE AND MAINTENANCE).
The dishes are not
clean.
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
Spray arms cannot rotate freely, being
hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS). Check that the upper rack is
in the correct position and adjust (lift up) if necessary.
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has
not been closed correctly.
Make sure the cap of the rinse aid dispenser is closed.
The lter is clogged with food residues or
limescale.
Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY).
The salt reservoir is empty. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not ll the
water.
The display
shows: H2O and
is lit; acoustic
alarm sounds.
No water in the water supply or the tap is
closed.
Make sure there is water in the water supply and the water tap is open.
The water inlet hose is kinked.
Check the inlet hose (see INSTALLATION). Close the door and press START/Pause button.
The screen in the water inlet hose is
clogged; it is necessary to clean it.
Check and clean the screen in the water inlet hose.
Close the door and press START/Pause button.
The dishwasher
nishes the cycle
prematurely.
The display
shows: F8 E3
The lter is clogged with food residues or
limescale.
Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and
DESCALE INSTRUCTION).
Drain hose positioned too low or siphoning
into the home sewage system.
Check if the end of the drain hose is placed at the correct height (see INSTALLATION).
Check for siphoning into the home sewage system, and install a siphon breaker/air
admittance valve if necessary.
An excessive amount of foam is present.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
Air in the water supply. Check water supply for leaks or other issues letting air inside.
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or is-
sues please contact authorized After-sales Service whose contact details can be found in the warranty booklet. Spare parts will be available
for aperiod of either up to 7 or up to 10 years, according to the specic Regulation requirements.
Bekijk gratis de handleiding van Whirlpool W8F HS61BS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | W8F HS61BS |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 34245 MB |
