Vulcan VS152001 handleiding
Handleiding
Je bekijkt pagina 6 van 44
6
The gap between grinding wheel (4) and the machined object support Grinding
(3) cannot exceed 2 mm and must be adjusted on a regular basis
Place the object to be ground on the machined object support (3) and
(see: Fig. B, p.2).
press it against the grinding wheel (4). For optimum grinding effect keep
moving the object slightly from one side to the other. This is the best way
NOTE: Adjustments can be made only when the grinding wheel is stopped.
both to provide optimum performance and uniform grinding wheel
If the grinding wheel is worn so much that it is not possible to adjust the
wear. Please note that objects being ground heat up intensely.
support gap as required, replace the grinding wheel.
Considering this, it is recommended to cool down the object machined
n Installing the anti-spark guards
from time to time.
Anti-spark guards (5) should be installed as shown in Fig. A2, p.2.
During operation the grinding wheel loses its process properties i.e.
The gap between grinding wheel (4) and an anti-spark guard (6) cannot
pores get clogged due to material penetrating inside and it loses its
exceed 2 mm and must be adjusted on a regular basis (see: Fig. B, p.2).
circular shape. To open the pores it is recommended to use diamond or
NOTE: Adjustments can be made only when the grinding wheel is stopped.
other dressers.
WARNING: Dusts of certain materials, for example, lead containing
n Replacing grinding wheels
paint coats, some wood types, minerals and some metals can be harmful.
NOTE: Protect the grinding wheel against falls, impacts and greasy
Direct physical exposure to dusts or inhaling them can result in allergic
contamination. It is prohibited to use the machine with grinding wheels
reactions and/or respiratory system diseases in operator and persons
damaged or non-compliant to specifications. Always check the grinding
staying in the working area. Some dusts, e.g. oak wood or beech wood
wheel for any damage before installation.
dust are considered to be carcinogenic, especially when combined with
Check grinding wheel using the so-called «sound» method. After placing
wood treatment chemicals (chromates, wood impregnates). Asbestos
your grinding wheel on a wooden bar turn and tap it with a mallet; the
containing materials can be machined by specially trained personnel
check should cover both sides of the grinding wheel and different
only.
distances from the hole:
– Always keep the workplace well ventilated.
a) pure metal sound: the grinding wheel is not damaged – it can be
– Dust masks are recommended.
used.
Observe all valid national and local regulations on handing materials to
b) rattling and quick stopping sound: the grinding wheel is cracked – it is
be machined.
not allowed to use it as using it can be dangerous to the user.
To replace a grinding wheel (4) use a Ph2 screwdriver and an M8 flat
MAINTENANCE AND STORAGE:
wrench to undo 3 fixing screws (8) and remove the side guard (9)
This power tool does not require any special maintenance. Store the
(see: Fig. C, p.2). Loosen the fixing nut (10) with an M19 flat wrench
machine in a place away from children, keep it clean and protect from
(NOTE: The left grinding wheel is fixed with a left-hand thread, the right
humidity and dust. Storage conditions should exclude any mechanical
cutting wheel is fixed with a right-hand thread) holding the nut fixing the
damage and weathering.
pressure flange from the other side. Then, remove pressure flange (11),
This device meets the requirements of both national and European
paper washer (12) and the grinding wheel off the spindle (13). Now you
standards and safety guidelines. Any repair should be carried out only by
can replace the grinding wheel. To install a new grinding wheel perform
qualified personnel using original spare parts.
the above steps in opposite direction. Pressure flanges should be pointed
n Cleaning
with their concave sides towards the grinding wheel.
NOTE: Before carrying out any cleaning unplug the machine from the
NOTE: After completing the replacement, the grinding wheel should run for
mains.
at least 1 minute with no load.
To provide safe and efficient operation it is recommended to clean the
tool directly after each use.
BEFORE YOU START OPERATION:
Remove any deposits using compressed air.
1. Make sure the power source parameters match the grinder
Clean the grinder housing with clean damp cloth and some soap. Do not
parameters provided on its nameplate.
use any cleaning agents and solvents, as they can damage machine
2. Make sure its switch (1) is in off position.
plastic components. Protect machine interior against water penetration.
3. When using an extension cord make sure its parameters and cable
cross-section meet the grinder power requirements. Extension cords
should be as short as possible. When in use extension cords must be
fully uncoiled.
4. Before you start operation check whether grinder fixing is secure,
making sure the grinding wheels move without any obstacles.
OPERATION:
Turning on/off
To turn the tool on set the switch (1) in position I.
To turn the tool off set the switch (1) in position 0.
NOTE: After changing or when starting operation, the grinding wheel
should run for at least 1 minute with no load.
n
NOTE:
n
PROTECTION OF THE ENVIRONMENT:
The symbol nearby denotes that old equipment must
never be thrown away together with other waste (with the
penalty of a fine). Hazardous components of electronic
equipment may adversely affect the natural environment
and human health.
Each household may contribute to the recovery and reuse (recycling) of
old machinery and equipment. Both in Poland and Europe a system for
recovery of used equipment either exists or is being created. The system
obliges all organizations that sell such equipment to collect the used
machinery and appliances. Moreover, general purpose collecting points
for such equipment are available.
Bekijk gratis de handleiding van Vulcan VS152001, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vulcan |
| Model | VS152001 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9316 MB |
