Vulcan VS152001 handleiding
Handleiding
Je bekijkt pagina 4 van 44
4
e) Power tools require maintenance. Check power tools for d) Use only grinding wheels recommended by the tool
concentricity or jamming of moving parts, any cracks and all manufacturer and marked with at least the same maximum
other factors affecting the power tool work safety. If any speed as the maximum speed permissible for the machine,
damage to the power tool is detected, it should be repaired as shown on its nameplate. The fact that a grinding wheel can be
before use. Improper power tool maintenance is a reason for many
installed on the machine does not guarantee its safe use.
accidents.
e) Under no circumstances are you allowed to use distorted or
damaged grinding wheels. Before each use always check the
f) Cutting tools should be sharp and clean. Keeping sharp cutting
grinding wheel for chips and cracks. Whenever you drop the
edges in good condition reduces the risk of jamming and facilitates
power tool or any grinding wheel, check it for damage and use other
operation.
undamaged grinding wheel, if necessary. Once the grinding wheel is
g) Power tools, equipment, working tools etc. should be used
checked and installed, start your power tool and allow it to run at
according to this user's manual taking into account
maximum speed for 1 minute, making sure that the user and any other
operating conditions and the work to be done. Misusing a
persons keep a safe distance from the grinding wheel working area.
power tool can result in dangerous situations.
f) Check the distance between the bench top on a regular
h) At low temperatures and after a long brakes in operation it is
basis. Set the anti-spark guard as often as it necessary to
recommended to turn the power tool to operate it with no
compensate for its wear and provide constant gap of not
load for a few minutes to provide proper grease distribution
more than 2 mm between the grinding wheel and its guard.
inside its driving mechanism.
When the gap exceeds the above mentioned value the protection is
i) Use soft, damp (cannot be wet) cloth and soap to clean power
compromised. The object machined can be drawn in when the grinding
tools. Do not use petrol, solvents and other agents that may
wheel rotates resulting in injuries to the operator.
damage your equipment.
g) Wear protective clothing (an apron). Make sure sparks
j) Power tools can be stored/carried after making sure that all
generated during operation do not reach anybody staying in
moving components are locked and protected against
the area. Remove any flammable materials from the
release with original devices intended for this purpose.
working zone.
k) Store power tools in a dry, dust and water-protected place.
h) Maximum permissible wheel speed cannot be lower than
l) Carry your power tool in its original packaging to provide
the maximum speed provided on machine's nameplate. The
protection against mechanical damage.
wheel rotating at a speed exceeding its permissible speed
can break or produce chips.
WARNING! General warnings regarding the use of
power tools.
WARNING! BENCH GRINDER, safety warnings
Repair:
Electrical safety:
a) Do not use a power tool with its power cord damaged. Do not
touch the power cord when damaged; in case of damaging
the power cord during operation unplug it from the mains.
Damaged power cords increase the risk of electric shock.
b) The power tool must be connected to a properly
grounded/earthed power source. A wall socket and any
extension cable must be fitted with a working protective (PE) conductor
of earthing system.
c) The grinding machine is equipped with an undetachable
power cord. If the undetachable power cord is damaged, it should be
replaced with a special cord or a set available from the manufacturer or
WARNING! BENCH GRINDER, safety warnings
a special repair shop.
Personal safety:
WARNING! BENCH GRINDER,
General safety warnings:
Always wear safety goggles
a) Place the material to be machined on the rotating grinding
wheel. The power tool can be switched off after removing
a) The power tool should be operated with anti-spark guard in
the material machined. The material machined can move abruptly.
place. Sparks produced during operation can result in eye injuries, and
setting objects in the area on fire.
b) Do not place the material to be machined on the grinding
wheel side. Always grind by moving the material forwards.
b) During operation anti-spark guards should be tilted
The object machined can be thrown out of your hand during grinding
downwards as much as possible. Machining metals generate
resulting in injuries.
sparks.
c) Never put hands under the grinding wheel while in motion.
c) Fix the grinding machine carefully to the bench using bolts
It can result in serious injuries.
or to any other stable surface to prevent any uncontrollable
a)
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.
Warranty and post-warranty repairs of its power tools are
carried out by PROFIX Service, which guarantees the best
quality or repair and use of genuine spare parts.
Bekijk gratis de handleiding van Vulcan VS152001, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vulcan |
| Model | VS152001 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9316 MB |
