Vulcan VJV10AL handleiding
Handleiding
Je bekijkt pagina 6 van 52
6
Using the charger:
a) Use only dedicated power adapters to charge the battery.
Application of a power adapter dedicated to charge another type of the
battery unit poses a risk of fires.
b) The supplied charger should only be used for charging batteries
that are supplied together with it. Charging other batteries may
cause breaking and disintegration of the battery, bodily harm, or fire.
c) Do not disassemble the charger.
d) The charger is designed exclusively for indoor use. It must not be
exposed to water or moisture.
e) Charge only in an ambient temperature between 15-25
degrees.
f) Do not insert metal objects of any kind into the charger.
APPLICATIONS AND CONSTRUCTION:
The device is dedicated to drive in and out screws, drilling boreholes in such
materials as steel, wood, plastics, etc.
The combo drill and screwdriver is designed exclusively for DIY applications.
The tool must not be used for work requiring a professional tool.
Any use of the that is not in observance with the above-mentioned device
purpose is forbidden, leads to the loss of warranty, and relieves the
manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the surroundings.
Despite using the tool according to its intended application it is impossible
to eliminate certain residual risk factors. Considering the tool construction
the following risks may occur when operating the tool:
- Touching the rotating drill bit with the hand or operator's clothes.
- Burns when changing drill bits (Drill bits heat up intensely during
operation; use protective gloves when changing the drill bit).
- Throwing back machined object or its fragment.
- Bending/breaking the drill.
n The set includes:
ź Cordless drill/Screwdriver -1pc.
ź Charger VJ1LD -1pc.(model VJV10AL)
ź Battery VJ2AK -1pc.(model VJV10AL)
ź 1pc.Operating instruction-
ź Warranty card - 1 pc.
n Device components (see page 2):
Fig.A 1. Keyless chuck
2. Clutch control knob
3. Gear shifter
4. Rotation direction switch
5. Fastener to hang on the belt
6. Battery*
7. Battery lock clip*
8. Auxiliary lighting
9. On/off switch
Fig.C 10. Charger*
11. Battery level indicator button*
12. Battery indicator to show the battery status of charge*
Fig.F 13. Clutch setting indicator
14. Drilling setting pictogram
Fig.G 15. Left-threaded fixing screw
* The accessories shown or described are not standard equipment
VJV10 model. For the complete offer of auxiliary equipment, see our
catalogue.
TECHNICAL PARAMETERS:
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of the
sequence of work operations.
The declared total vibrations and declared noise emissions were measured
in accordance with a standard test method and may be used for tool
comparison.
The declared total vibrations and noise emissions can be used in preliminary
exposure assessment.
Warnings:
The vibrations and noise emissions during the actual use of the power tool
may differ from the declared values depending on how the tool is used and
on the type of the workpiece in particular.
Determine safeguards to protect the operator. They should be based on the
estimated exposure under actual operational conditions (taking into
account all parts of the operating cycle such as when the tool is switched off
or idle except the start time).
PREPARATION FOR WORK:
Prior to each use of the tool one has to check whether moving parts of the
device are in operating conditions, not seized, cracked or damaged that may
affect proper operation of the tool. Damaged tools must be handed over for
repairs before they can be used again.
n Charging the battery
NOTE! Model VJV10 delivered without battery and charger. Depending on
your needs, you can purchase a 2.0 Ah battery VJ2AK or 4.0Ah VJ4AK and a
compatible charger VJ1LD (charging time 1-2 hours).
You can check the battery level with the battery level indicator button (11).
A single LED means the battery level is low, two LEDs mean medium level,
Recommended 20 V Li-ion batteries: VJ2AK (2Ah), VJ4AK (4Ah)
Recommend chargers: VJ1LD (1h)
Rotation speed under no-load conditions (Gear I/II)
Supply voltage
Chuck clamping range
Gear shifter I-II
Maximum torque
Maximum drilling
diameter
Wood
Steel
Acoustic pressure level(LpA)
Acoustic power (LwA)
Vibration level according to EN 628-2-1, drilling in
metal a (Tolerance of measurements K=1,5 m/s²)
h, D
Weight (with battery)
n =0-400 / 0-1400/min
o
20 V d.c.
yes
2
1,083 m/s
87,4 dB(A)
76,4 dB(A)
1,4 kg
13 mm
25 mm
ø 0,8-10 mm
35 Nm
Tolerance of measurements K K
LpA, LwA
5 dB(A)
Bekijk gratis de handleiding van Vulcan VJV10AL, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vulcan |
| Model | VJV10AL |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9934 MB |
