Vonroc S_JS506DC handleiding
Handleiding
Je bekijkt pagina 10 van 124
10
EN
WWW.VONROC.COM
Mounting the saw blade
Make sure the blade holder is free of material
debris (such as splinters of wood or metal).
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Insert the saw blade in the chuck (16). Check
that the saw blade is securely fixed and that the
teeth are pointing in the cutting direction.
3. Let go of the clamping lever. Check whether
the back of the saw blade is positioned in the
centre of the guide roller (10).
Make sure to use the right sawblade for the corres-
ponding material. Included with the machine is a
coarse sawblade for wood and a fine sawblade for
metal and plastics.
Removing the saw blade
1. Turn the clamping lever (13) as far to the left as
possible and hold it in this position.
2. Remove the saw blade from the chuck (16).
3. Let go of the clamping lever.
Attaching the parallel guide (Fig. D)
1. Loosen the wing bolts (14).
2.
Mount the parallel guide (19) onto the baseplate
(9).
3. Set the desired cutting width using the scale
on the parallel guide (14) and the cutting mark
on the baseplate (20). The cutting mark (20)
indicates the position of the saw blade.
4. Tighten the wing bolt (14).
Mounting / Dismounting the Glide Shoe (Fig. E)
To protect the surface of the material to be proces-
sed, the glide shoe is already mounted. The glide
shoe can be removed if necessary.
1. Remove the battery (5) from the device.
2. Release both retaining clips at the rear of the
glide shoe (8).
3. Slide the glide shoe (8) forward, carefully det-
aching the front part of the glide shoe from the
base plate (9).
4. Pull the glide shoe (8) downwards.
5. To reattach the glide shoe (8), first slide it onto
the base plate (9) at the front.
6. Then lock the retaining clips at the rear. Check
that the glide shoe (8) is securely fastened.
7. Reinsert the battery (5).
Mounting / Dismounting the Chip Break Protection
(Fig. E)
With a chip break protection (already pre-installed),
the chipping of the wood surface during sawing
can be prevented. The chip break protection can
only be used at a saw angle of 0°. It can be remo-
ved if necessary, for example, if you want to make
a miter cut.
1. Remove the battery (5) from the device.
2. First, disassemble the glide shoe (8).
3. Remove the chip break protection (11) from
the base plate (9) by carefully pressing the chip
break protection (11) outwards.
4.
To reinstall the chip break protection (11), careful-
ly press it back into the recess on the base plate
(9) from below until the chip break protection (11)
locks. Ensure that the smooth side of the chip
break protection (11) faces away from the device.
5. Reinsert the battery (5).
4. OPERATION
Switching the machine on/off (Fig. A)
The on/off switch (2) is used for activating the
machine and adjusting speed.
• To start the machine, press and hold the lock-
off button (1) and press the on/off switch (2).
• The further the on/off switch (2) is being
pushed, the faster the blade will move. The
required speeds depends on the material and
can be determined by practical testing.
• To stop the machine, release the on/off switch (2).
Adjusting the bevel angle (Fig. B, F)
1. Loosen the bolt (18), using the hex key (15).
2. Adjust the baseplate (9) to the desired position
(0°- 45°).
The sawing angle (bevel) can be read on the
scale (7).
3. Tighten the bolt (7), using the hex key (15). It is
possible to store the hex key onto the machine,
as shown on Fig. B.
Adjusting the pendulum action (Fig. A)
The pendulum action switch is used to set the way
in which the teeth of the saw blade grip the material.
The pendulum action switch can be set to 4 positions:
0 - No pendulum action
1 - Small pendulum action
2 - Medium pendulum action
3 - Large pendulum action
Bekijk gratis de handleiding van Vonroc S_JS506DC, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vonroc |
| Model | S_JS506DC |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14997 MB |
