Vimar RS13 handleiding
Handleiding
Je bekijkt pagina 11 van 32

9
IMPORTANT INSTRUCTIONS
FOR THE SAFETY
ATTENTION - FOR THE SAFETY OF PEOPLE IT IS IMPORTANT TO
FOLLOW ALL THE INSTRUCTIONS
KEEP THESE INSTRUCTIONS WITH CARE
1° - If it is not forecast in the electric gearcase, install a switch of
magnetothermic type upstream, (omni polar with minimum port of
the contacts of 3mm) with a check of conformity to the international
standards. Such devise must be protected against the accidental
lockup (for example by installing inside a locked board).
2° - For the section and the type of the cables ELVOX advices to use
a cable of H05RN-F type with 1,5 sqmm minimum section and,
however, to keep to the IEC 3120 and installation standards in
force in your country.
3° - Positioning of a possible couple of photoelectric cells: the radius of
the photoelectric cells must be at a height of no more than 70 cm
from the ground and at a distance not superior to 20 cm from the
motion plane of the door. Their correct working must be verified at
the end of the installation in accordance with point 7.2.1 of the EN
12445.
4° - To fulfil the limits set by EN 12453, and in case the peak force
exceeds the normative limit of 400 N it is necessary to have
recourse to the active presence survey on the whole height of the
door (up to max 2,5 m) - The photoelectric cells, in this case, must
be applied to the outside and the inside to a distance from the
plan of movement of the door not advanced to 20 cm, every
60÷70 cm for all the height of the door until to a maximum of 2,5 m
(EN 12445 point 7.3.2.1)
N.B.: The earthing of the system is obligatory.
The data described in this handbook are purely a guide.
ELVOX reserves the right to change them in any moment.
Carry out the system in the respect of the standards and laws in force.
4° - Check frequently the system, in particular cables, springs and
supports to find out possible unbalances, wear signs or damages.
The final user must not operate electrically the horizontally
pivoted door if this needs maintenance or repair, since a failure
in the installation or a non correctly balanced barrier can provoke
wounds.
5° - Before proceeding with the installation, the installer must forecast
the risks analysis of the final automatized closing and the and the
safety of the identified dangerous points (Following the standards
EN 12453/EN 12445).
6° - Before installing the motion motor, the installer must verify that
the door is in good mechanical conditions and that it adequately
opens and closes.
7° - The installer must install the member for the manual release at a
height inferior to 1,8 m.
8° - The installer will have to remove possible impediments to the
motorized motion of the door (eg. Door bolts, sliding bolts, door
locks etc.)
9° - The installer will permanently have to put the tags warning
against the deflection on a very visible point or near possible fixed
controls.
10° - The wiring harness of the different electric components external to
the operator (for example photoelectric cells, flashlights etc.) must
be carried out according to the EN 60204-1 and the modifications
to it done in the point 5.2.2 of the EN 12453.
11° - Keep the automatism controls (push-button panel, remote control
etc.) out of the children way. The controls must be placed at a
minimum height of 1,5 m from the ground and outside the range of
the mobile parts.
12° - Before carrying out any installation, regulation or maintenance
operation of the system, take off the voltage by operating on the
special magnetothermic switch connected upstream.
13° - At the end of the installation, the installer will have to make sure
that the parts of the door do not encumber streets or public
sidewalks.
14° - At the end of the installation, the installer will have to make sure
that the motion motor prevents or blocks the opening motion when
the door is loaded with a 20 kg weight, fixed in the middle of the
inferior edge of the door.
THE ELVOX COMPANY DOES NOT ACCEPT ANY RESPONSIBILITY
for possible damages caused by the non observance during the
installation of the safety standards and of the laws in force at present.
IMPORTANT SAFETY INSTRUCTIONS
FOR THE INSTALLATION
ATTENTION - THE INCORRECT INSTALLATION
CAN CAUSE SERIOUS DAMAGES
FOLLOW ALL INSTALLATION INSTRUCTIONS
1° - This handbook is exclusively addressed to the specialized
personnel who knows the constructive criteria and the protection
devices against the accidents for motorized gates, doors and main
doors (follow the standards and the laws in force).
2° - The installer will have to issue a handbook to the final user in
accordance with the 12635.
3° - The installer will have to put the tags warning against the
entrapping dangers near the controls and the horizontally pivoted
door.
Directive 2002/96/EC (WEEE)
The crossed-out wheelie bin symbol marked on the product indicates that at the end of its useful life, the product must be handled separately from
household refuse and must therefore be assigned to a differentiated collection centre for electrical and electronic equipment or returned to the dealer upon
purchase of a new, equivalent item of equipment.
The user is responsible for assigning the equipment, at the end of its life, to the appropriate collection facilities.
Suitable differentiated collection, for the purpose of subsequent recycling of decommissioned equipment and environmentally compatible treatment and
disposal, helps prevent potential negative effects on health and the environment and promotes the recycling of the materials of which the product is
made. For further details regarding the collection systems available, contact your local waste disposal service or the shop from which the equipment was
purchased.
Risks connected to substances considered as dangerous (WEEE).
According to the WEEE Directive, substances since long usually used on electric and electronic appliances are considered dangerous for people
and the environment. The adequate differentiated collection for the subsequent dispatch of the appliance for the recycling, treatment and dismantling
(compatible with the environment) help to avoid possible negative effects on the environment and health and promote the recycling of material with
which the product is compound.
EN
Bekijk gratis de handleiding van Vimar RS13, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
Merk | Vimar |
Model | RS13 |
Categorie | Niet gecategoriseerd |
Taal | Nederlands |
Grootte | 6937 MB |