Vestil S-2CB-62 handleiding
Handleiding
Je bekijkt pagina 3 van 16

S-2CB, Manual.doc
Copyright 2015 Vestil Manufacturing Corp. Page 3 of 16
SAFETY GUIDELINES
Failure to read and understand the instructions included in this manual before using or servicing the
pallet truck constitutes misuse of the product. Study the entire manual before you use the truck for the
first time and before each subsequent use. Read the manual to refresh your understanding of the safe use and
maintenance procedures on p. 50-51. If questions remain after you finish reading the manual, contact Vestil for
answers. DO NOT attempt to resolve any problem with the truck unless you are certain
that it will be safe to use
afterwards.
To decrease the risk of electrocution:
DO NOT contact or operate the pallet truck close to electrified wires or other sources of electricity;
Before operating theS-2CB, always inspect the area where you will use it.
Improper use might result in serious personal injuries to the operator and/or bystanders. To
minimize the possibility of injury, ALL persons who might operate, perform maintenance on, or service the S-2CB
must read, understand and apply the following instructions:
DO NOT operate the S-2CB unless and until you are:
1. Trained to use the machine; AND
2. Certified as a trained operator by your employer in accordance with U.S. OSHA regulations (29 CFR
§1910.178) and any standards incorporated by reference (e.g. ANSI/ITSDF B56.1-2005).
DO NOT attempt to lift or transport loads that exceed the rated capacity.
Inspect the machine before each use; DO NOT use the EPT unless it is in normal condition. Normal operating
condition exists if the S-2CB passes the inspection and functions tests described under the heading, “Inspect
& Perform a Functions Tests” on p. 14.
DO NOT use the unit until you read and understand the entire owner’s manual. Review the manual before
each use AND before performing maintenance on the device.
DO NOT use the S-2CB if the load-supporting elements sustain any structural damage. Structural elements
include, but are not limited to, the forks, carriage, and wheels. If structural damage is present, immediately
tag the unit “Out of Service” and inform maintenance personnel of the problem.
DO NOT use the S-2CB if it makes unusual noises during operation.
DO NOT allow people to ride on the stacker. Only the operator of S-2CB equipped with a properly
installed rider platform.
DO NOT attempt to lift an unevenly distributed load. Always center and evenly distribute the load on the forks.
DO NOT operate the S-2CB on surfaces (ramps or grades).
DO NOT leave the S-2CB unattended while it supports a load. Always fully lower the forks, and then
completely disengage the skid or pallet.
DO NOT modify the stacker without first receiving written authorization from Vestil. Unauthorized
modifications may make the S-2CB unsafe to use.
To maximize the service life of the S-2CB and to prevent damage:
Always store the machine in a secure, dry location where it will not interfere with traffic or other activities.
Maintain the product as suggested in “Maintenance & Inspections”.
REMOVING THE Coounter-Balance Stacker FROM THE SHIPPING PALLET:
Counter-Balance stacker is s
hipped in ready-to-use condition. However, it must first be removed from the shipping pallet
before it can be used for the first time.
DO NOT attempt to drive the Stacker off of the pallet; it might tip over and cause bodily injuries or
property damage. To minimize the risk of injury to yourself or other persons, perform the following steps to
remove the machine from the shipping pallet:
1. Remove all packing material.
2. Inform all personnel not participating in the unpacking process to clear the area.
3.
Lift the S-2CB off of the pallet using a hoist or a with a capacity of at least 4
,000 pounds. Always
apply the proper hoisting procedures or forklift operation practices you learned during your training program.
Bekijk gratis de handleiding van Vestil S-2CB-62, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
Merk | Vestil |
Model | S-2CB-62 |
Categorie | Vorkheftruck |
Taal | Nederlands |
Grootte | 2183 MB |