Vestil PS-4045 handleiding
Handleiding
Je bekijkt pagina 6 van 8
Rev. 7/8/2016 PS-4045, MANUAL.doc
Copyright 2016 Vestil Manufacturing Co. Page 6 of 8
Inspections & Maintenance:
If any of the inspections described below reveal problems with the stand, remove it from service and tag it “Out of
Service”. Restore the unit to normal operating condition BEFORE using it again.
A. Before each use, inspect the following components. Each component must be in normal operating condition. To
establish normal operating condition, make a thorough record of the appearance of the various parts of the stand
when you first receive it. Compare later observations to this record to determine whether the machine is in normal
operating condition.
1. Frame: examine the base, scissor legs, tabletop, and carousel (if equipped with this option). Look for damaged
welds, warps, cracks, or other deformations.
2. Casters (only units equipped with caster kit option PS-RF-CK): examine each caster. Confirm that casters are
not severely worn, that the wheels rotate freely, that both swivel casters swivel properly, and that the brakes
firmly engage the wheels.
3. Springs: The springs should stretch uniformly and equally, and should resist movement of the legs. Apply the
load/pallet to the stand. Listen for unusual sounds and watch for unusual movement. If you notice anything
atypical, unload the stand and determine the cause of the issue.
4. Fasteners: check nuts and bolts. Make sure all fasteners are tightly connected.
5. Roller bearings (only units equipped with carousel option): rotate the carousel. Watch and listen to the carousel
as it rotates. If unusual noise is produced, or if the carousel binds, wobbles, or lurches, remove it and examine
the roller bearings. Rotate each bearing to determine if it requires lubrication. Replace all bearings that are
significantly worn. Clean the underside of the carriage where the bearings make contact with it to remove debris
that might interfere with bearing movement.
B. At least once per month:
1. Clean the entire stand: remove dirt and other matter from all surfaces.
2. Labels: refer to the “Labeling Diagram” on p. 7. Make sure that all labels are in place, undamaged, and
readable.
3. Fasten the weldments (2) to the bottom of
the pallet stand.
a. Align the mounting tabs on the
underside of the stand with the
mounting tabs on the caster bracket
weldments.
b. Then, insert hex head bolts (9) through
the tabs and secure the bolts with flat
washers and lock nuts (10 & 11).
4. Attach the clamping brackets.
a. Insert 1
1
/
2
” carriage bolts up through
each clamping tabs (see Step 2 on p.
5) of both caster weldments (1).
b. Put a clamping bracket onto the end of
each bolt. The flat end of the brackets
should overlap the base frame.
c. Secure the bolts with flat washers (6) and lock nuts (7).
5. Attach the casters.
a. Install the caster bracket of a caster into each of the 4 caster receivers as diagrammed above (swivel casters
in back; rigid casters in front).
b. Insert a 5” carriage bolt (3) bolt through the bolts holes in each of the caster receivers. Tighten the
corresponding lock nut on the end of the bolt to secure the caster inside its re
ceiver.
Clamping
bracket
Carriage
bolt
Caster
receiver
Swivel
caster
Rigid
caster
Caster
brake
Flat washer
& lock nut
Base
frame
5” carriage bolt
& nut combo.
Bekijk gratis de handleiding van Vestil PS-4045, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | PS-4045 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2742 MB |
