Vestil LM-1T-8-24 handleiding
Handleiding
Je bekijkt pagina 10 van 14
Table of Contents Rev. 9/25/2023 LM-1T-8-24-TP/HBE MANUAL
Table of Contents Copyright 2022 Vestil Manufacturing Co. Page 10 of 14
Accessing the Power Unit & Battery Charger
The power unit is housed in the space between the fork
tubes and the bottom of the boom receiver. It is protected
by 2 cover pieces that fasten to the frame. See Items 34 &
35 in the EXPLODED VIEW on p. 4. Access the power unit by
removing 1 or both of the covers. Each cover is fastened to
the frame with a
5
/
16
”-18x
1
/
2
” thread-cutting screw (item 36
on p. 4). Remove the screws; then lift the covers and set
them aside.
The power unit includes an on-board battery charger.
The charger is connected to a 3-prong inlet integrated into
the rear plate of the frame. A cover protects the inlet. To
recharge the battery, open the cover and connect a 3-
prong extension cord to the inlet. Use the shortest extension
cord possible to recharge the battery.
Contact TECHNICAL SERVICE to discuss problems with
the power unit or battery charger.
RECORD OF SATISFACTORY CONDITION
Before puting the boom into service, make a detailed record of its appearance and functions. Thoroughly
photograph the unit and all labels applied to it. Closely photograph both of the hooks and shackles, fork tubes,
the power unit, hydraulic hoses (LM-1T-8-24-HBE-TP), and the handheld controller and its electrical cord. Add
the photographs to the record. Extend and retract the boom. Describe the motion of the boom and sounds
heard as it moves. Include a description of the sound level. Attach a test load to the boom. The load should
weigh no more than 2000 lb. (909.1kg). Extend and retract the boom again and record your observations.
Measure the throat opening of each hook. Add the measurements to the record. This record establishes
satisfactory condition. Compare results of future inspections to the record to determine whether a part is in
satisfactory condition. Repair or replace all parts that are not in satisfactory condition. Contact TECHNICAL
SERVICE to order replacement parts.
LOAD TESTS
After creating a RECORD OF SATISFACTORY CONDITION and before using the boom for the first time, a
qualified person should conduct a load test. The test load should be 125% of the rated load (capacity) of the
boom. For instance, if the rated load (capacity) is 1,000 lb. (454.5kg) the test load should be 1,250 pounds
(568.2kg). Raise the load off of the ground until it is entirely suspended from the boom. Leave the load
suspended for a few minutes. Return it to the ground and unload the boom. Perform a Monthly Inspection as
described in the INSPECTIONS section (p. 10). The boom should undergo load testing immediately after it is
repaired or modified. Never modify the boom without first receiving written approval from Vestil.
NOTE: If your boom is used with a lift truck whose capacity is less than 125% of the rated load of your boom PLUS
the weight of the boom, then load testing as described above should not be performed. Instead, the boom
must be rerated (capacity reduced) and be tested with an appropriate load weight for your lift truck. The
boom must also be relabeled to reflect the rerated capacity. Mark/label the truck to identify the boom, show
the weight of the truck and boom combination, and show the capacity of the truck with the boom at
maximum elevation with the load laterally centered. Use the LOAD TEST RECORD page at the end of this
manual to record the weight used to load test your boom based on the rerated capacity.
INSPECTIONS
Inspections and repairs should only be performed by qualified persons. Compare the results of each
inspection to the RECORD OF SATISFACTORY CONDITION (the “RECORD”). Do not use the boom unless all parts
are in satisfactory condition. Replace parts that are not in satisfactory condition before using the boom again.
DON’T GUESS! If you have any questions about the condition of your boom, contact the TECHNICAL SERVICE
department. The phone number is provided on the cover page of this manual. Never make temporary repairs
of damaged or missing parts. Only use manufacturer-approved replacement parts. Replace the entire unit if it
cannot be restored to satisfactory condition.
3-prong outlet
with cover
Thread-
cutting
screws
Cover (left side)
Opening for
handheld controller
cord
Bekijk gratis de handleiding van Vestil LM-1T-8-24, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | LM-1T-8-24 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3367 MB |
