Vestil JIB-HC-3 handleiding
Handleiding
Je bekijkt pagina 5 van 10
Rev. 10/17/2016 JIB-HC, MANUAL
Copyright 2016 Vestil Manufacturing Co. Page 5 of 10
Assembly Instructions:
NOTE: Numbers in parentheses correspond to parts numbers in the exploded parts diagrams on pp. 3-5.
Step 1: Drill
13
/
16
” holes in the
locations shown on a steel column;
then fasten the brackets (28-016-
021) to the column with
3
/
4
” fasteners
of suitable length (selected by your
building engineer).
FIG. 4: JIB-HC-20 Exploded Parts Diagram and Bill of Materials
Item
No.
Part No. Description Qty.
1 28-514-055 Weldment, I-beam subassembly 1
2 28-514-054 Frame, upper bearing subassembly 1
3 28-112-001 Axle, pivot wall bracket, formed 2
4 28-145-004 Adjustable yoke end, small 2
5 28-014-052 Frame, tie rod support, formed 1
6 28-112-043 Pin,
3
/
4
” x 2” retaining clevis, zinc-plated 2
7 28-111-004 Bearing, sleeve, pivot spacer 2
8 28-016-021 Bracket, wall mounting 2
9 33098 1
1
/
8
” SAE flat washer, zinc-plated 4
10 37048 Nylock nut, zinc-plated, 1
1
/
8
” – 7, grade 2 4
11 65078 Extended prong cotter pin, zinc finish,
1
/
8
” x 1
1
/
2
” 2
12 36266
3
/
4
” – 20, hex jam nut, zinc-plated 2
37
5
/
8
”
33
5
/
8
”
29
5
/
8
”
3
3
/
8
”
(1
11
/
16
” on either side of
center line)
Center line
Steel column
Step 2: Set the upper bearing on top of the sleeve bearing and set them
inside the upper bracket; then insert the axle through the bracket and
bearing. Install washers and lock nuts as shown below. Set the end of
the I-beam on top of a sleeve bearing and put them in the lower bracket.
Install the axle and hardware as shown below. Do not overtighten the
lock nuts. A gap of ~
1
/
4
” should be present between the top of the
bracket and the sleeve bearing or I-beam bearing.
Bracket
Axle (28-112-001)
Sleeve bearing (28-111-004)
Flat washer (33098)
Lock nut (37048)
Flat washer (33098)
Lock nut (37048)
Lower bracket (28-016-021)
I-beam
Upper bearing (28-514-054)
Lock nut (37048)
Flat washer (33098)
Axle (28-112-001)
Sleeve bearing (28-111-004)
Flat washer (33098)
Lock nut (37048)
NOTE: Position the
axles so that equal
numbers of thread
stick out above and
below the brackets.
NOTE: Position the
axles so that equal
numbers of thread
stick out above and
below the brackets.
Upper bracket (28-016-021)
1
/
4
” gap between top of bearing and underside of bracket
1
/
4
” gap between top of bearing and underside of bracket
Bekijk gratis de handleiding van Vestil JIB-HC-3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | JIB-HC-3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2200 MB |
